Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2016.05
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076218 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1237  Speed Sensor Rotor Faulty  C1275  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1277  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The skid control ECU measures the speed of each wheel by receiving signals from the speed sensor.

These signals are used for recognizing that all four wheels are operating properly.

Therefore, all wheel signals must be equal.

DTCs C1275 to C1278 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1275 to C1278 are output only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1237 Speed Sensor Rotor Faulty Any of the following is detected:
1.

Discrepancy among four wheel speed sensor output.

2.

Abnormal pulse signals from 3 or more sensors.

3.

Continuous ABS control is performed for 60 seconds or more.


·

Tire and wheel size

·

Tire deformation

·

Speed sensor rotor

·

Speed sensor

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)
C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)
C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)
C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

HINT:
·

DTC C1275 is for the front speed sensor RH.

·

DTC C1276 is for the front speed sensor LH.

·

DTC C1277 is for the rear speed sensor RH.

·

DTC C1278 is for the rear speed sensor LH.



WIRING DIAGRAM

Refer to DTCs C1330, C1331, C1332, C1333, C1464, C1465, C1466 and C1467.

for front: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1271

for rear: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1273

CAUTION / NOTICE / HINT

HINT:

When C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 is output together with C1237, inspect and repair the trouble areas indicated by C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 first.

for front: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1271

for rear: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1273


PROCEDURE

1.CHECK TIRES
a.

Check the size and condition of all four wheels.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION

HINT:

The DTC is output when tire deformation or a difference in tire size is detected.


OK:

The diameter of all four tires and the tire pressure are the same.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (SPEED SENSOR)

NG

REPLACE TIRES SO THAT ALL FOUR TIRES ARE THE SAME SIZE

2.READ VALUE USING INTELLIGENT TESTER (SPEED SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4

d.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.



Result:
Result Proceed to
OK A
NG (for front) B
NG (for rear) C



A

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

B

5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

C

12.INSPECT SKID CONTROL SENSOR WIRE
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check using the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode DTCs are not output.



Result:
Result Proceed to
OK A
NG (for front) B
NG (for rear) C



A

4.RECONFIRM DTC

B

5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

C

12.INSPECT SKID CONTROL SENSOR WIRE
4.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1237 is not output. A
DTC C1237 is output (for front). B
DTC C1237 is output (for rear). C



A

B

8.REPLACE FRONT SPEED SENSOR

C

15.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR
a.

Remove the front speed sensor and the component with the sensor rotor.

for speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for sensor rotor: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>REMOVAL


b.

Check the speed sensor tip and speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the sensor tip and rotor.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Install the front speed sensor and the component with the sensor rotor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A49 skid control ECU connector and the A53 or A16 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A49-16 (FR+) - A53-1 (FR+) Always Below 1 Ω
A49-16 (FR+) - Body ground Always 10 kΩ or higher
A49-4 (FR-) - A53-2 (FR-) Always Below 1 Ω
A49-4 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A49-19 (FL+) - A16-1 (FL+) Always Below 1 Ω
A49-19 (FL+) - Body ground Always 10 kΩ or higher
A49-8 (FL-) - A16-2 (FL-) Always Below 1 Ω
A49-8 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC
a.

Reconnect the A49 skid control ECU connector and the A53 or A16 front speed sensor connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

8.REPLACE FRONT SPEED SENSOR

B

8.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

10.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY

B

END

10.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the front speed sensor rotor (front drive outboard joint shaft assembly).

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>REMOVAL

HINT:

If the front speed sensor rotor needs to be replaced, replace the front drive outboard joint shaft assembly.


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

B

END

12.INSPECT SKID CONTROL SENSOR WIRE
a.
C275487C01
0.188,0.677 0.51,0.906 0.323,0.229 1.823,0.698 2.146,0.927 0.323,0.229 0.198,2.844 0.521,3.073 0.323,0.229 1.833,2.865 2.156,3.094 0.323,0.229 0.563,2.073 0.969,1.333 false 2.219,2.073 2.427,1.573 false 1.552,2.073 1.229,1.323 false 2.938,2.073 2.667,1.594 false 1.563,4.396 1.24,3.646 false 0.552,4.385 0.958,3.646 false 2.125,4.406 2.333,3.906 false 2.948,4.396 2.677,3.917 false 0.25,0.125 0.563,0.323 0.313,0.198 10 *a 0.25,0.354 0.563,0.552 0.313,0.198 10 *A 0.281,0.708 0.594,0.906 0.313,0.198 10 h1 1.875,0.729 2.188,0.927 0.313,0.198 10 hO1 1.021,0.51 1.333,0.708 0.313,0.198 10 *b 2.396,0.552 2.708,0.75 0.313,0.198 10 *c 0.302,2.563 0.615,2.76 0.313,0.198 10 *B 0.313,2.875 0.625,3.073 0.313,0.198 10 i1 1.906,2.896 2.219,3.094 0.313,0.198 10 iN1 2.417,3.073 2.729,3.271 0.313,0.198 10 *c 1.01,2.896 1.323,3.094 0.313,0.198 10 *b 0.448,2.094 0.906,2.292 0.458,0.198 10 RR- 1.406,2.094 1.865,2.292 0.458,0.198 10 RR+ 2.115,2.094 2.573,2.292 0.458,0.198 10 RR+ 2.771,2.094 3.229,2.292 0.458,0.198 10 RR- 0.417,4.417 0.875,4.615 0.458,0.198 10 RL- 1.469,4.427 1.927,4.625 0.458,0.198 10 RL+ 1.938,4.438 2.396,4.635 0.458,0.198 10 RL+ 2.885,4.427 3.344,4.625 0.458,0.198 10 RL-
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Remove the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
h1-2 (RR+) - hO1-1 (RR+) Always Below 1 Ω
h1-2 (RR+) - hO1-2 (RR-) Always 10 kΩ or higher
h1-2 (RR+) - Body ground Always 10 kΩ or higher
h1-1 (RR-) - hO1-2 (RR-) Always Below 1 Ω
h1-1 (RR-) - hO1-1 (RR+) Always 10 kΩ or higher
h1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
i1-2 (RL+) - iN1-1 (RL+) Always Below 1 Ω
i1-2 (RL+) - iN1-2 (RL-) Always 10 kΩ or higher
i1-2 (RL+) - Body ground Always 10 kΩ or higher
i1-1 (RL-) - iN1-2 (RL-) Always Below 1 Ω
i1-1 (RL-) - iN1-1 (RL+) Always 10 kΩ or higher
i1-1 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)

NG

13.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A49-17 (RR+) - hO1-1 (RR+) Always Below 1 Ω
A49-17 (RR+) - Body ground Always 10 kΩ or higher
A49-29 (RR-) - hO1-2 (RR-) Always Below 1 Ω
A49-29 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A49-31 (RL+) - iN1-1 (RL+) Always Below 1 Ω
A49-31 (RL+) - Body ground Always 10 kΩ or higher
A49-18 (RL-) - iN1-2 (RL-) Always Below 1 Ω
A49-18 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.RECONFIRM DTC
a.

Install the skid control sensor wire.


b.

Reconnect the A49 skid control ECU connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

15.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

15.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

16.RECONFIRM DTC
16.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

B

END