The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.
DTC C1281 is cleared when the Lost Booster Pressure Judgment Check is performed correctly in Test Mode and the check indicates a pass, or when Test Mode ends. DTC C1281 is output only in Test Mode.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1246 | Master Cylinder Pressure Sensor Malfunction | Any of the following is detected:
1.
The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V). 2.
An abnormality is detected in the skid control ECU internal sensor test. 3.
The sensor signal offset value is out of range. |
·
Stop light switch circuit ·
Master cylinder pressure sensor circuit ·
Master cylinder pressure sensor (Brake actuator assembly) |
| C1281 | Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) | Detected only during Test Mode. | ·
Stop light switch assembly ·
Brake pedal load sensing switch (Brake pedal support assembly) ·
Brake booster assembly ·
Master cylinder pressure sensor (Brake actuator assembly) |
Refer to DTCs C1249 and C1429.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1429
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List using the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Master Cylinder Sensor | Master cylinder pressure sensor reading | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.20 to 0.40 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Master Cylinder Sensor |
Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the intelligent tester changes when the brake pedal is depressed.
When the pedal is depressed, the voltage displayed on the intelligent tester increases.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Select the Data List using the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch | ON or OFF | ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point |
- |
| Tester Display |
|---|
| Stop Light SW |
| Brake Pedal Load Sensing SW |
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.
The intelligent tester displays on or off according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn on.
First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The stop light switch does not turn on.) | B |
| NG (Turning on of the brake pedal load sensing switch is not confirmed.) | C |
| NG (The brake pedal load sensing switch turns on first.) | D |
A
B
C
D
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
At a speed of 30 km/h (18 mph) or more, drive the vehicle and perform a braking test (decelerate the vehicle by depressing the brake pedal).
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1246 is not output. | A |
| DTC C1246 is output. | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| A49-30 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A40 brake pedal load sensing switch connector.
Do not remove the brake pedal load sensing switch from the brake pedal support assembly.
When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (FSW+) - 1 (FSW-) | Switch OFF
(Brake pedal depressed) |
950 to 1050 Ω |
| 2 (FSW+) - 1 (FSW-) | Switch ON
(Brake pedal released) |
203 to 223 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-34 (FSW+) - A40-2 (FSW+) | Always | Below 1 Ω |
| A49-34 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A40-1 (FSW-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Check the brake pedal height and stop light switch assembly installation.
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT
The brake pedal height and stop light switch assembly installation are normal.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D