Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1234  Yaw Rate Sensor  C1472  Acceleration Sensor  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

HINT:

If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0123 (Lost Communication with Yaw Rate Sensor Module) is output. When U0123 is output together with C1234 and/or C1472, inspect and repair the trouble areas indicated by U0123 first.


DTCs may be stored if one of the following occurs:

·

Yaw rate and acceleration sensor circuit malfunction.

·

Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.

·

Yaw rate and acceleration sensor signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1234 Yaw Rate Sensor Any of the following is detected:
1.

The yaw rate sensor offset value is estimated as less than -5.25 deg/s or more than 5.25 deg/s based on offset correction performed when the vehicle is stopped and then the vehicle starts off.

2.

The offset correction did not complete with the vehicle stopped, and the yaw rate sensor offset value is estimated as less than -15 deg/s or more than 15 deg/s based on the offset correction performed while the vehicle is being driven.

3.

The offset correction completed with the vehicle stopped and the yaw rate sensor offset value is less than -7.5 deg/s or more than 7.5 deg/s.

4.

The yaw rate sensor offset value is estimated as less than -7.5 deg/s or more than 7.5 deg/s based on the offset correction performed while the vehicle is being driven.

5.

After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 5 seconds or more when the vehicle is stopped.

6.

After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more when the vehicle starts off.

7.

After the VSC system has started, but before the vehicle has started off, as the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more.

8.

The yaw rate sensor value is less than -94.75 deg/s or more than 94.75 deg/s for 0.8 seconds or more.

9.

The change of the yaw rate sensor value within 0.04 seconds is abnormal.

10.

The value from the yaw rate sensor is judged as abnormal based on the skid control ECU estimation.


·

Sensor installation

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Yaw rate and acceleration sensor circuit


C1472 Acceleration Sensor Any of the following is detected:
1.

With the vehicle stopped, the internal acceleration value is less than -7 m/s2 or more than 7 m/s2 for 0.4 seconds or more.

2.

The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed while the vehicle is being driven.

3.

The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2 for 0.8 seconds or more.


·

Sensor installation

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Yaw rate and acceleration sensor circuit



WIRING DIAGRAM

C239282E03
0.105,3.939 0.38,4.095 0.275,0.156 10 I47 5.494,4.093 7.05,4.448 1.556,0.355 10 Skid Control ECU (Brake Actuator Assembly) 6.056,1.323 6.484,1.472 0.427,0.149 10 CANH 6.056,0.701 6.484,0.85 0.427,0.149 10 CANL 5.494,3.939 5.759,4.1 0.265,0.161 10 A49 5.8,1.214 6.0,1.375 0.2,0.161 10 26 5.8,0.611 6.0,0.772 0.2,0.161 10 14 3.895,1.937 5.299,2.278 1.404,0.341 10 from Ignition Switch*1 or IG2 Relay*2 2.36,2.058 2.643,2.211 0.283,0.153 10 A/B 1.284,1.833 1.479,2.004 0.195,0.171 10 21 1.284,1.214 1.479,1.385 0.195,0.171 10 13 1.284,0.611 1.465,0.782 0.181,0.171 10 22 0.779,1.323 1.206,1.472 0.427,0.149 10 CANH 0.933,1.929 1.235,2.078 0.302,0.149 10 IG2 1.007,2.548 1.236,2.697 0.229,0.149 10 E1 0.793,0.701 1.22,0.85 0.427,0.149 10 CANL 0.105,4.093 2.288,4.417 2.183,0.324 10 Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 1.007,3.178 1.236,3.327 0.229,0.149 10 E2 1.284,2.45 1.479,2.62 0.195,0.171 10 25 1.284,3.08 1.479,3.251 0.195,0.171 10 26 2.648,4.095 5.024,4.255 2.376,0.16 10 *1: w/o Smart Entry and Start System 2.648,4.403 5.024,4.564 2.376,0.16 10 *2: w/ Smart Entry and Start System


CAUTION / NOTICE / HINT

HINT:

When U0123 and/or U0126 is output together with C1234 and/or C1472, inspect and repair the trouble areas indicated by U0123 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

At a speed of 30 km/h (18 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTC is not output. A
CAN communication system DTC is output. B



A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The ECU should be tightened to the specified torque.

The ECU should not be tilted.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C239271C08
0.25,0.708 0.729,1 0.479,0.292 1.042,2.177 0.573,2.792 false 0.417,0.781 0.823,1.042 0.406,0.26 10 I47 0.24,0.219 0.667,0.604 0.427,0.385 10 *a 0.385,2.823 0.719,3.052 0.333,0.229 10 IG2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the I47 yaw rate and acceleration sensor (airbag sensor assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C239271C09
0.25,0.708 0.729,1 0.479,0.292 1.646,2.188 1.198,2.813 false 1.823,2.188 2.271,2.813 false 0.406,0.781 0.781,1.063 0.375,0.281 10 I47 0.24,0.219 0.583,0.635 0.344,0.417 10 *a 1.052,2.844 1.5,3.167 0.448,0.323 10 E1 2.208,2.844 2.563,3.156 0.354,0.313 10 E2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Always Below 1 Ω
I47-26 (E2) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)