Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014605 DOOR LOCK _0074106 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function(s) does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

WIRING DIAGRAM

B281171E25
0.365,3.375 0.646,3.563 0.281,0.188 10 A15 0.552,2.875 0.698,3.073 0.146,0.198 10 2 1.729,2.875 1.875,3.073 0.146,0.198 10 1 0.365,3.552 2.073,3.781 1.708,0.229 10 Wireless Door Lock Buzzer 2.156,2.875 2.375,3.104 0.219,0.229 10 22 3.625,3 3.979,3.229 0.354,0.229 10 BZR 2,4.667 2.229,4.813 0.229,0.146 10 3D 2.792,3.802 3.135,4.021 0.344,0.219 10 MB 3.385,2.865 3.594,3.083 0.208,0.219 10 21 5.833,0.542 6.135,0.781 0.302,0.24 10 HAZ 3.365,0.531 3.823,0.76 0.458,0.229 10 GND 3.24,0.438 3.375,0.677 0.135,0.24 10 6 2.792,3.99 4.406,4.417 1.615,0.427 10 Main Body ECU (Multiplex Network Body ECU) 2,4.813 4.677,5.094 2.677,0.281 10 Instrument Panel Junction Block Assembly 5.677,0.438 5.802,0.667 0.125,0.229 10 5 5.26,2.573 7.115,2.792 1.854,0.219 10 Combination Meter Assembly 0.75,5.438 2.563,5.646 1.813,0.208 10 : CAN Communication Line 4.146,0.521 4.521,0.75 0.375,0.229 10 HAZ 4.51,0.438 4.615,0.625 0.104,0.188 10 4 2.958,0.927 3.188,1.167 0.229,0.24 10 I56 2.958,1.083 5.083,1.479 2.125,0.396 10 Air Conditioning Control Assembly (Hazard Switch) 5.26,2.438 5.5,2.656 0.24,0.219 10 I17

CAUTION / NOTICE / HINT

NOTICE:

The wireless door lock control system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ANSWER-BACK OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Utility / Customize / Wireless Door Lock.


e.

Select the setting by referring to the table below.

Wireless Door Lock
Tester Display Description Default Setting ECU
Hazard Answer Back When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Resp Wireless door lock buzzer response ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Vol Wireless door lock buzzer volume Level 5 0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 Main body ECU (Multiplex network body ECU)
50006 1

Result:
Result Proceed to
Both items are ON and except Level 0 A
Either item is OFF or Level 0 B



A

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

B

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock operates normally. A
Wireless door lock/unlock does not operate normally. B



A

3.READ VALUE USING INTELLIGENT TESTER (DOOR UNLOCK DETECTION SWITCH)

B

3.READ VALUE USING INTELLIGENT TESTER (DOOR UNLOCK DETECTION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
RR-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
*1
RL-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
*2
·

*1: When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.

·

*2: When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.


Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52
OK:

The intelligent tester should display as shown in the table according to door lock operation.



Result:
Result Proceed to
OK A
NG (for Driver door) B
NG (for Front Passenger door) C
NG (for Rear LH door) D
NG (for Rear RH door) E



A

4.CHECK WIRELESS ANSWER-BACK OPERATION

B

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

C

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

D

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

E

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Only wireless door lock buzzer answer-back does not occur. A
Only hazard warning light answer-back does not occur. B



A

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER)

B

10.CHECK HAZARD WARNING LIGHTS OPERATION
5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

Result:
Result Proceed to
Wireless door lock buzzer does not turn on/off. A
Wireless door lock buzzer turns on/off. B



A

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A15 wireless door lock buzzer and 3D instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-1 - 3D-22 Always Below 1 Ω
A15-2 - Body ground Always Below 1 Ω
A15-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B217457C07
1.219,0.333 1.552,0.542 0.333,0.208 4.938,0.625 5.271,0.833 0.333,0.208 5.583,1.167 5.823,1.51 false 0.167,0.063 0.563,0.302 0.396,0.24 10 *a 1.313,0.354 1.833,0.635 0.521,0.281 10 3D 5,0.646 5.438,0.948 0.438,0.302 10 MB 5.677,1.51 6.208,1.75 0.531,0.24 10 BZR
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-22 - MB-21 (BZR) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.REPLACE WIRELESS DOOR LOCK BUZZER

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Temporarily replace the wireless door lock buzzer with a new one.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
a.

Check the operation of the wireless answer-back function.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless answer-back function operates normally.



Result:
Proceed to
OK
NG



OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

10.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning light blinks when the hazard warning signal switch is pressed.

OK:

Hazard warning light signal is normal.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit)