Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM19V0EQ _59 Vehicle Exterior _014619 MIRROR (EXT) _0074232 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Reverse Shift-linked Function of Power Mirrors does not Operate  


SYSTEM DESCRIPTION

On receiving a reverse signal from the park/neutral position switch assembly, the ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU. Each outer mirror control ECU then performs control in response to the reverse signal.

HINT:

The reverse shift-linked function will not activate when the mirror select switch is in the neutral position (off).


WIRING DIAGRAM

B295639E30
5.823,2.042 7.104,2.448 1.281,0.406 10 false Outer Rear View Mirror Assembly RH 4.854,0.458 5.417,0.781 0.563,0.323 10 false RM+R 4.042,1.906 4.375,2.146 0.333,0.24 10 false z7 4.823,1.375 5.458,1.688 0.635,0.313 10 false RMVR 4.594,0.99 5.135,1.365 0.542,0.375 10 false CAN 2.969,0.385 3.417,0.667 0.448,0.281 10 false CAN 3.313,0.99 3.792,1.24 0.479,0.25 10 false CAN 0.708,0.396 1.115,0.708 0.406,0.313 10 false CAN 4.594,3.698 5.073,3.969 0.479,0.271 10 false CAN 5.313,0.365 5.583,0.646 0.271,0.281 10 false 10 5.333,1.25 5.542,1.51 0.208,0.26 10 false 1 4.865,3.208 5.417,3.5 0.552,0.292 10 false LM+R 3.49,4.646 3.844,4.927 0.354,0.281 10 false z6 4.844,4.083 5.365,4.313 0.521,0.229 10 false LMVR 5.313,3.083 5.646,3.344 0.333,0.26 10 false 10 5.333,3.958 5.469,4.198 0.135,0.24 10 false 1 5.875,4.75 7.125,5.188 1.25,0.438 10 false Outer Rear View Mirror Assembly LH 4.021,2.042 5.604,2.552 1.583,0.51 10 false Outer Mirror Control ECU Assembly (Driver Door) 2.49,4.063 4.146,4.49 1.656,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 1.344,2.99 2.677,3.448 1.333,0.458 10 false Park/Neutral Position Switch Assembly 0.51,4.281 0.938,4.615 0.427,0.333 10 false ECM 0.51,4.115 0.896,4.396 0.385,0.281 10 false E26 1.344,2.833 1.531,2.979 0.188,0.146 10 false E4 0.885,2.333 1.271,2.615 0.385,0.281 10 false R 0.885,1.552 1.125,1.813 0.24,0.26 10 false P 1.698,2.333 2.031,2.563 0.333,0.229 10 false RL 1.698,1.552 1.938,1.75 0.24,0.198 10 false PL 1.083,1.438 1.458,1.688 0.375,0.25 10 false 70 1.073,2.208 1.51,2.49 0.438,0.281 10 false 68 1.563,1.438 1.802,1.688 0.24,0.25 10 false 3 1.563,2.208 1.729,2.417 0.167,0.208 10 false 2 1.823,5.344 3.74,5.594 1.917,0.25 10 false : CAN Communication Line 3.49,4.781 5.698,5.208 2.208,0.427 10 false Outer Mirror Control ECU Assembly (Front Passenger Door)

CAUTION / NOTICE / HINT

HINT:

The reverse shift-linked function will not activate when the mirror select switch is in the neutral position (off).


PROCEDURE

1.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C09
0.156,0.063 0.313,0.229 0.156,0.167 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

Result:
Result Proceed to
Memory and reactivation functions are normal. A
Memory function is not normal. B
Reactivation function is not normal. C




A

2.CHECK CAN COMMUNICATION SYSTEM

B

GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirror Surface Position is not Memorized)

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirrors do not Return to Memorized Position)

2.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTC is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

3.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Check if SFI system DTCs are output.

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

SFI system DTCs are not output.


Result:
Proceed to
OK
NG




OK

4.CHECK COMBINATION METER ASSEMBLY

NG

GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

4.CHECK COMBINATION METER ASSEMBLY
a.

Check if the shift position indicator light in the combination meter assembly operates normally.

OK:

The shift position indicator light indicates the actual shift position correctly.



Result:
Proceed to
OK
NG



OK

5.CHECK REVERSE SHIFT-LINKED FUNCTION

NG

GO TO METER / GAUGE SYSTEM (PROBLEM SYMPTOMS TABLE)

5.CHECK REVERSE SHIFT-LINKED FUNCTION
a.
B294057C01
0.177,0.052 0.354,0.25 0.177,0.198 10 *a
*a Downward


Turn the engine switch on (IG).


b.

Set the mirror select switch to L or R.


c.

Check that the mirror surface turns downward when the shift lever is moved to R.

Result:
Result Proceed to
Reverse shift-linked functions on both mirrors are not normal A
Reverse shift-linked function on RH side is not normal B
Reverse shift-linked function on LH side is not normal C




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

C

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)