Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM19V0EQ _59 Vehicle Exterior _014619 MIRROR (EXT) _0074232 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Wireless Transmitter Memory Function does not Operate  


DESCRIPTION

Key IDs can be registered (linked) with either the M1 or M2 seat memory switches. The key ID registration procedure should be performed while the electrical key transmitter is in the vehicle, the engine switch is on (IG), and the driver door is closed. When registration is completed, the buzzer will sound as an answerback.

PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Power door lock operation is normal.



Result:
Proceed to
OK
NG



OK

2.CHECK SMART ENTRY AND START SYSTEM (ENTRY FUNCTION)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (PROBLEM SYMPTOMS TABLE)

2.CHECK SMART ENTRY AND START SYSTEM (ENTRY FUNCTION)
a.

Check the smart entry and start system (entry function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Smart entry and start system (entry function) is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK MEMORY AND REACTIVATION FUNCTION

NG

3.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C10
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is stored.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the stored fully left position.

Result:
Result Proceed to
Memory and reactivation function is normal A
Memory function is not normal B
Reactivation function is not normal C




A

4.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirror Surface Position is not Memorized)

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirrors do not Return to Memorized Position)

4.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Driver door courtesy switch condition ON or OFF ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed)
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy
50003 123 197
OK:

ON or OFF appears on the screen.



Result:
Proceed to
OK
NG



OK

5.PERFORM ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY RECOGNITION CODE REGISTRATION

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

5.PERFORM ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY RECOGNITION CODE REGISTRATION
a.

With the engine switch on (IG) and the driver door closed, press and hold the M1 or M2 switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code registration mode to allow a key to be linked to mirror surface memory position.

HINT:

If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.



b.

When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds once (0.5 seconds).

OK:

The buzzer sounds when registration is completed.



Result:
Proceed to
OK
NG



OK

6.PERFORM MEMORY DELETION

NG

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
6.PERFORM MEMORY DELETION
a.

Enter the following menus: Body / Main Body / Data List.


b.

After performing any of the following procedures to cut the link between the key and switch, check that the Data List for the applicable key changes to NONE.


c.

With the engine switch on (IG) and the driver door closed, press and hold the SET switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code deletion mode.

HINT:

If the memory switch is released before entering deletion mode, the memory switch will not enter deletion mode.



d.

When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds twice (0.1 seconds each time).

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1
MEM SW2: M2 linked with key ID1
MEM SW3: M3 linked with key ID1*
-
Mem SW No. w/KeyID2 Switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2
MEM SW2: M2 linked with key ID2
MEM SW3: M3 linked with key ID2*
-
Mem SW No. w/KeyID3 Switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3
MEM SW2: M2 linked with key ID3
MEM SW3: M3 linked with key ID3*
-
Mem SW No. w/KeyID4 Switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4
MEM SW2: M2 linked with key ID4
MEM SW3: M3 linked with key ID4*
-
Mem SW No. w/KeyID5 Switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5
MEM SW2: M2 linked with key ID5
MEM SW3: M3 linked with key ID5*
-
Mem SW No. w/KeyID6 Switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6
MEM SW2: M2 linked with key ID6
MEM SW3: M3 linked with key ID6*
-
Mem SW No. w/KeyID7 Switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7
MEM SW2: M2 linked with key ID7
MEM SW3: M3 linked with key ID7*
-

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191
OK:

The Data List display for the applicable key changes to NONE.



Result:
Proceed to
OK
NG



OK

7.PERFORM MEMORY REGISTRATION

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.PERFORM MEMORY REGISTRATION
a.

After performing any of the following procedures to link the key and a switch, check the Data List to confirm that the key and switch have been linked.


b.

With the engine switch on (IG) and the driver door closed, press and hold the M1 or M2 switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code registration mode to allow a key to be linked to mirror surface memory position.

HINT:

If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.



c.

When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly LH sounds once (0.5 seconds).

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1
MEM SW2: M2 linked with key ID1
MEM SW3: M3 linked with key ID1*
-
Mem SW No. w/KeyID2 Switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2
MEM SW2: M2 linked with key ID2
MEM SW3: M3 linked with key ID2*
-
Mem SW No. w/KeyID3 Switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3
MEM SW2: M2 linked with key ID3
MEM SW3: M3 linked with key ID3*
-
Mem SW No. w/KeyID4 Switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4
MEM SW2: M2 linked with key ID4
MEM SW3: M3 linked with key ID4*
-
Mem SW No. w/KeyID5 Switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5
MEM SW2: M2 linked with key ID5
MEM SW3: M3 linked with key ID5*
-
Mem SW No. w/KeyID6 Switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6
MEM SW2: M2 linked with key ID6
MEM SW3: M3 linked with key ID6*
-
Mem SW No. w/KeyID7 Switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7
MEM SW2: M2 linked with key ID7
MEM SW3: M3 linked with key ID7*
-

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191
OK:

Data List shows that the key ID has been linked to a switch (M1 or M2).



Result:
Proceed to
OK
NG



OK

8.CHECK MEMORY CALL REACTIVATION FUNCTION

NG

10.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
8.CHECK MEMORY CALL REACTIVATION FUNCTION
a.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.

OK:

Memory call reactivation function is normal.




Result:
Proceed to
OK
NG



OK

NG

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Enter the following menus: Body / Driver Seat / Active Test.


b.

Perform Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer built into the position control ECU and switch assembly ON or OFF -
Body Electrical > Driver Seat > Active Test
Tester Display
Buzzer
50004 162 5
OK:

The buzzer sounds.



Result:
Proceed to
OK
NG



OK

10.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POSITION CONTROL ECU & SWITCH ASSEMBLY

10.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.PERFORM MEMORY REGISTRATION
11.PERFORM MEMORY REGISTRATION
a.

After performing any of the following procedures to link the key and a switch, check the Data List to confirm that the key and switch have been linked.


b.

With the engine switch on (IG) and the driver door closed, press and hold the M1 or M2 switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code registration mode to allow a key to be linked to mirror surface memory position.

HINT:

If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.



c.

When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds once (0.5 seconds).

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1
MEM SW2: M2 linked with key ID1
MEM SW3: M3 linked with key ID1*
-
Mem SW No. w/KeyID2 Switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2
MEM SW2: M2 linked with key ID2
MEM SW3: M3 linked with key ID2*
-
Mem SW No. w/KeyID3 Switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3
MEM SW2: M2 linked with key ID3
MEM SW3: M3 linked with key ID3*
-
Mem SW No. w/KeyID4 Switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4
MEM SW2: M2 linked with key ID4
MEM SW3: M3 linked with key ID4*
-
Mem SW No. w/KeyID5 Switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5
MEM SW2: M2 linked with key ID5
MEM SW3: M3 linked with key ID5*
-
Mem SW No. w/KeyID6 Switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6
MEM SW2: M2 linked with key ID6
MEM SW3: M3 linked with key ID6*
-
Mem SW No. w/KeyID7 Switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7
MEM SW2: M2 linked with key ID7
MEM SW3: M3 linked with key ID7*
-

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191
OK:

The Data List shows that the key ID has been linked to a switch (M1 or M2).



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)