Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Not Using the Engine Support Bridge) › from 2013.07
RM19V0EQ _53 Suspension _014588 FRONT SUSPENSION _0074023 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

Install 9 hole plugs to the front frame assembly.


Hide 52217E 2.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C238985C03
0.175,0.109 0.345,0.258 0.17,0.149 10 *a
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting rear cushion LH while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting rear cushion LH in the correct direction.



b.
C169232C04
1.198,1.5 1.417,1.5 1.417,1.5 1.531,2.125 false 2.49,0.854 2.01,0.854 false 2.198,2.698 2.521,2.698 false 1.01,1.427 1.188,1.594 0.177,0.167 10 *1 2.542,0.771 2.865,0.938 0.323,0.167 10 SST 2.542,2.615 2.865,2.781 0.323,0.167 10 SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.
C167152C02
1.646,1.5 2.052,1.5 false 0.563,2.229 0.979,2.323 false 2.396,0.854 2.302,0.854 2.302,0.854 2.24,0.792 false 0.969,3.156 0.833,3.156 0.833,3.156 0.771,3.083 false 2.406,0.76 2.625,0.938 0.219,0.177 10 *a 2.083,1.406 2.438,1.573 0.354,0.167 10 SST 1,3.052 1.333,3.219 0.333,0.167 10 *b 0.198,2.146 0.552,2.313 0.354,0.167 10 SST
*a Hold
*b Turn


Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.

NOTICE:

Check that there is no clearance between the front suspension member and the front suspension member body mounting rear cushion LH.



Hide 52215 3.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

a.
C238987C03
0.166,0.121 0.339,0.271 0.173,0.15 10 *a
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting rear cushion RH while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting rear cushion RH in the correct direction.



b.

Install SST using the same procedure as the front suspension member body mounting rear cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.

Using SST, install the front suspension member body mounting rear cushion RH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

HINT:

Perform the same procedure as the LH side.



Hide 52211J 4.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C238988C04
0.157,0.121 0.31,0.274 0.152,0.152 10 *a
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting front cushion while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting front cushion in the correct direction.



b.

Install SST using the same procedure as the front suspension member body mounting rear cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.
C167148C02
2.271,0.74 2.479,0.74 false 1.646,1.354 2.125,1.198 false 0.771,2.292 0.969,2.406 false 1.042,3.021 1.25,3.073 false 2.5,0.646 2.688,0.802 0.188,0.156 10 *a 1.26,3 1.604,3.177 0.344,0.177 10 *b 0.49,2.208 0.802,2.375 0.313,0.167 10 SST 2.167,1.104 2.479,1.271 0.313,0.167 10 SST
*a Hold
*b Turn


Using SST, install the front suspension member body mounting front cushion as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Check that there is no clearance between the front suspension member and the front suspension member body mounting front cushion.



Hide 52216B 5.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Install the 2 front suspension member body mounting rear stoppers to the front frame assembly.


Hide 52213A 6.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Install the 2 front suspension member body mounting front stoppers to the front frame assembly.


Hide 51227B 7.INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER

a.

Install the front suspension member dynamic damper to the front frame assembly with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48069 8.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly.


b.
C167143E01
0.656,0.357 0.795,0.515 0.139,0.158 10 1 1.147,0.24 1.286,0.398 0.139,0.158 10 2 2.467,0.926 2.613,1.077 0.146,0.150 10 3

Install the front lower No. 1 suspension arm sub-assembly to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt 1, 2 : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt 3 : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

While keeping the nut from rotating, tighten the bolt.



Hide 48068 9.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 10.INSTALL STEERING LINK ASSEMBLY

Hide 11.INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer bar with 2 front stabilizer link assemblies to the front frame assembly.


Hide 48829A 12.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 13.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as the LH side.


Hide 51100G 14.INSTALL FRONT FRAME ASSEMBLY