When the manual transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the manual transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust from the moving section could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
1.REMOVE ENGINE STAND
Using a chain block and engine sling device, secure the engine assembly.
Adjust the angle of the sling device carefully to prevent the engine assembly or engine hanger from deforming or becoming damaged.
Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.
Remove the engine stand from the engine.
32101
2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
30500
3.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
12315A
4.INSTALL ENGINE MOUNTING BRACKET RH
Install the engine mounting bracket RH with the 3 bolts.
43457
5.INSTALL DRIVE SHAFT BEARING BRACKET
Install the drive shaft bearing bracket with the 3 bolts.
12361A
6.TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR
Temporarily install the front engine mounting insulator with the bolt.
12372A
7.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH
Temporarily install the engine mounting insulator LH with the nut.
12362A
8.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH
Temporarily install the engine mounting insulator RH with the nut.
51100G
9.INSTALL FRONT FRAME ASSEMBLY
Install the front frame assembly with the 9 nuts.
| *a | Front Side | *b | RH Side |
| *c | LH Side | - | - |
Install the 4 hole plugs.
Tighten the bolt and 2 nuts.
| *a | Front Side | *b | LH Side |
| *c | RH Side | - | - |
43420G
10.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
43420
11.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
43410
12.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
27020
13.INSTALL GENERATOR ASSEMBLY
88310
14.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY
16361A
15.INSTALL V-RIBBED BELT
82121
16.INSTALL ENGINE WIRE
Install the engine wire to the engine with transaxle.
17.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.
Do not position a height adjustment attachment or plate lift attachment onto the front frame assembly.
To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.
Make sure to support the engine assembly with transaxle securely to prevent it from falling.
Remove the engine hangers.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE UNIT>REMOVAL
Install the engine assembly to the vehicle.
Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine is clear of all wiring and hoses.
While raising the engine into the vehicle, do not allow it to contact the vehicle.
Install the frame side rail plate RH and LH with the 4 bolts and 2 nuts.
Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
32101A
18.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
| *1 | Adhesive |
Apply a few drops of adhesive to the first 2 or 3 threads of the 6 drive plate and torque converter assembly setting bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Turn the crankshaft to gain access to the installation locations of the 6 torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.
Install the black colored bolt first, and then the 5 silver colored bolts.
11361J
19.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover.
45220
20.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
43502C
21.INSTALL FRONT AXLE ASSEMBLY LH
43501C
22.INSTALL FRONT AXLE ASSEMBLY RH
Use the same procedure described for the LH side.
48069
23.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
24.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
45470
25.INSTALL TIE ROD ASSEMBLY LH
45460
26.INSTALL TIE ROD ASSEMBLY RH
Use the same procedure described for the LH side.
89543
27.INSTALL FRONT SPEED SENSOR LH
89542
28.INSTALL FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
48810
29.INSTALL FRONT STABILIZER LINK ASSEMBLY LH
48820B
30.INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
43502H
31.INSTALL FRONT AXLE SHAFT NUT LH
43501H
32.INSTALL FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
17410
33.INSTALL FRONT EXHAUST PIPE ASSEMBLY
23901
34.CONNECT FUEL TUBE SUB-ASSEMBLY
Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.
Check for damage or contamination on the connected part of the pipe.
Check if the pipe and the connector are securely connected by trying to pull them apart.
Install the No. 1 fuel pipe clamp.
88711
35.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
88704
36.INSTALL SUCTION HOSE SUB-ASSEMBLY
44774
37.CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)
Connect the union to connector tube hose.
44773F
38.CONNECT UNION TO CHECK VALVE HOSE (for RHD)
Connect the union to check valve hose.
12309
39.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY
Temporarily install the engine moving control rod sub-assembly with the 4 bolts.
Fully tighten the engine moving control rod sub-assembly with the 4 bolts.
82284
40.INSTALL EARTH WIRE
Install the earth wire with the bolt.
12327A
41.INSTALL NO. 2 ENGINE MOUNTING STAY RH
Install the No. 2 engine mounting stay RH with the 2 bolts.
33820B
42.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.
Connect the transmission control cable assembly to the control shaft lever with the nut.
Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.
Connect the wire harness clamp.
17771A
43.INSTALL NO. 1 AIR CLEANER BRACKET
Install the No. 1 air cleaner bracket to the battery carrier with the bolt.
Connect the 2 wire clamps.
82121
44.CONNECT ENGINE WIRE
Connect the 2 wire clamps.
Connect the connector to the ECM with the lock lever.
Connect the engine wire to the engine room relay block.
Connect the wire clamp and install the 2 nuts.
Install the No. 1 relay block cover.
28100
45.INSTALL STARTER ASSEMBLY
87245
46.CONNECT INLET HEATER WATER HOSE
Connect the inlet heater water hose.
87246
47.CONNECT OUTLET HEATER WATER HOSE (for LHD)
Connect the outlet heater water hose.
87246
48.CONNECT OUTLET HEATER WATER HOSE (for RHD)
Connect the 3 heater outlet water hoses.
32941
49.CONNECT INLET NO. 1 OIL COOLER HOSE
Connect the inlet No. 1 oil cooler hose to the automatic transaxle assembly.
32942
50.CONNECT OUTLET NO. 1 OIL COOLER HOSE
Connect the outlet No. 1 oil cooler hose to the automatic transaxle assembly.
16571C
51.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose.
Connect the air fuel ratio sensor wire to the No. 1 radiator hose with the hose clamp.
16572D
52.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose.
53.INSTALL BATTERY
Install the battery and battery tray.
Install the battery clamp with the bolt and nut.
Connect the positive (+) battery terminal
54.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
| *1 | Hole |
| *2 | Projection |
Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.
Tighten the 2 bolts.
Connect the wire harness clamp.
17801
55.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
56.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
17750A
57.INSTALL INLET AIR CLEANER ASSEMBLY
Install the inlet air cleaner assembly with the 2 bolts.
58.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
59.ADD ENGINE OIL
60.ADD ENGINE COOLANT
61.ADD AUTOMATIC TRANSAXLE FLUID
62. CHARGE WITH REFRIGERANT
63. WARM UP ENGINE
64.INSPECT FOR FUEL LEAK
65.INSPECT FOR OIL LEAK
66.INSPECT FOR COOLANT LEAK
67.INSPECT FOR EXHAUST GAS LEAK
68.INSPECT REFRIGERANT LEAK
69.INSPECT IGNITION TIMING
70.INSPECT ENGINE IDLE SPEED
71.INSPECT CO/HC
12601B
72.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
Engage the 3 pins and install the No.1 engine cover sub-assembly.
73.INSPECT AND ADJUST SHIFT LEVER POSITION
53737B
74.INSTALL FRONT FENDER APRON SEAL LH
53736
75.INSTALL FRONT FENDER APRON SEAL RH
51442C
76.INSTALL ENGINE UNDER COVER LH
53852K
77.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)
51441C
78.INSTALL ENGINE UNDER COVER RH
53851Z
79.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)
80.INSTALL FRONT WHEEL
81.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
82.CHECK FOR SPEED SENSOR SIGNAL