1.INSTALL PARKING BRAKE SHOE LEVER
for PBR Made:
Install the parking brake shoe lever.
2.INSTALL DUST COVER
for PBR Made:
Install the dust cover to the parking brake shoe lever as shown in the illustration.
Using an air riveter or a hand riveter with a nose piece, install the boot retainer on the back plate with 2 new rivets.
If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.
Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
Confirm that the rivets are seated properly against the boot retainer.
Do not tilt the riveter when installing the rivet onto the boot retainer.
Do not leave any space between the rivet head and boot retainer.
Do not leave any space between the boot retainer and the parking brake plate sub-assembly. Firmly hold the 2 items together while installing the rivet.
3.INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY
for PBR Made:
Install the parking brake shoe plate sub-assembly.
4.INSTALL DUST PLATE
for PBR Made:
Install the dust plate to the parking brake plate sub-assembly.
42450B
5.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY
for PBR Made: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSTALLATION
89516D
6.CONNECT SKID CONTROL SENSOR WIRE
for PBR Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION
7.INSTALL PARKING BRAKE SHOE HOLD PLATE
for PBR Made:
Install the parking brake shoe hold plate with a new parking brake shoe hold bolt.
8.INSTALL ADJUSTMENT PAWL
for PBR Made:
Install the adjustment pawl.
9.INSTALL NUT AND SCREW ADJUSTING ASSEMBLY
for PBR Made:
|
High Temperature Grease |
Apply high temperature grease to the parking brake plate sub-assembly as shown in the illustration.
Install the nut and screw adjusting assembly, parking brake tappet and parking brake push rod.
46430
10.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY
for PBR Made: Click hereBrake>PARKING BRAKE>PARKING BRAKE CABLE>INSTALLATION
11.INSTALL PARKING BRAKE SHOE ASSEMBLY
for PBR Made:
Install the parking brake shoe assembly as shown in the illustration.
There should be no oil or grease on the friction surface of the lining and disc.
47456A
12.INSTALL PARKING BRAKE SHOE GUIDE PLATE
for ADVICS Made:
Install the parking brake shoe guide plate with the parking brake shoe guide plate set bolt.
13.APPLY HIGH TEMPERATURE GREASE
for ADVICS Made:
|
High Temperature Grease |
Apply high temperature grease to the areas of the parking brake plate which make contact with the shoes as shown in the illustration.
47447E
14.INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN
for ADVICS Made Front Side:
Install the 2 parking brake shoe hold down spring cups, parking brake shoe hold down spring and parking brake shoe hold down spring pin.
for ADVICS Made Rear Side:
Install the 2 parking brake shoe hold down spring cups, parking brake shoe hold down spring and parking brake shoe hold down spring pin.
47612
15.INSTALL PARKING BRAKE SHOE LEVER
for ADVICS Made:
|
High Temperature Grease |
Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.
Temporarily install the parking brake shoe lever to the No. 2 parking brake shoe assembly with a new parking brake shoe type C washer.
Using a feeler gauge, measure the clearance between the No. 2 parking brake shoe assembly and parking brake shoe lever.
Less than 0.35 mm (0.0137 in.)
If the clearance is not as specified, replace the parking brake shoe shim with one of the correct size.
| Part No. | Shim Thickness |
|---|---|
| 90564-09184 | 0.3 mm (0.0118 in.) |
| 90564-09185 | 0.6 mm (0.0236 in.) |
| 90564-09186 | 0.9 mm (0.0354 in.) |
Select a parking brake shoe shim and install it and the parking brake shoe type C washer.
Using a pair of pliers, squeeze together the ends of the parking brake shoe type C washer.
Check that the parking brake shoe lever moves smoothly.
47612
16.CONNECT PARKING BRAKE SHOE LEVER
for ADVICS Made:
Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever.
46550E
17.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)
for ADVICS Made:
Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.
46580
18.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY
for ADVICS Made:
Install the No. 1 parking brake shoe assembly to the parking brake shoe return tension spring.
47406A
19.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET
for ADVICS Made:
|
High Temperature Grease |
Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.
Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.
|
High Temperature Grease |
Apply high temperature grease to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly as shown in the illustration.
Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the parking brake plate.
Make sure that the parking brake shoe lever does not separate from the No. 2 parking brake shoe assembly.
46590
20.CONNECT NO. 2 PARKING BRAKE SHOE ASSEMBLY
for ADVICS Made:
Engage the claw of the parking brake shoe hold down spring cup to the No. 2 parking brake shoe assembly.
46580
21.CONNECT NO. 1 PARKING BRAKE SHOE ASSEMBLY
for ADVICS Made:
Engage the claw of the parking brake shoe hold down spring cup to the No. 1 parking brake shoe assembly.
47613D
22.INSTALL PARKING BRAKE SHOE STRUT COMPRESSION SPRING
for ADVICS Made:
Install the parking brake shoe strut compression spring.
47614
23.INSTALL PARKING BRAKE SHOE STRUT
for ADVICS Made:
Install the parking brake shoe strut.
Install the No. 1 parking brake shoe assembly.
46550G
24.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)
for ADVICS Made Front Side:
Install the parking brake shoe return tension spring.
for ADVICS Made Rear Side:
Install the parking brake shoe return tension spring.
25. CHECK PARKING BRAKE INSTALLATION
for ADVICS Made:
Check that each part is installed properly.
| *A | LH Side | *B | RH Side |
|
Front of the Vehicle | - | - |
There should be no oil or grease on the friction surfaces of the shoe linings or discs.
26.INSPECT REAR AXLE HUB BEARING LOOSENESS
for PBR Made: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>ON-VEHICLE INSPECTION
27.INSPECT REAR AXLE HUB RUNOUT
for PBR Made: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>ON-VEHICLE INSPECTION
42431
28.INSTALL REAR DISC
42491
29.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
30.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
31.INSTALL REAR WHEEL
32.ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for LHD)
33.ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for RHD)