1.INSTALL AIR CONDITIONING UNIT ASSEMBLY
Install the air conditioning unit assembly to the instrument panel reinforcement assembly with the 3 bolts.
Tighten the bolts in the order shown in the illustration to install the air conditioning unit assembly.
2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT
Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When installing the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Engage the 3 guides and temporarily install the instrument panel reinforcement assembly with air conditioning unit as shown in the illustration.
Install the instrument panel reinforcement assembly with the 3 bolts <A> and 2 new bolts <B>.
| *1 | Movable Collar | *2 | Body |
| *3 | Instrument Panel Reinforcement | - | - |
| *a | Step 1 | *b | Step 2 |
| *c | Step 3 | *d | Step 4 |
Tighten the bolts in the order shown in the illustration to install the reinforcement assembly.
Install the instrument panel reinforcement assembly with air conditioning unit with the nut.
Install the bolt.
Install the 2 bolts.
Tighten the bolts in the order shown in the illustration.
Engage each clamp.
Connect the connector.
Connect the connector holder with the 2 nuts.
Install the bolt and connect the earth wires.
Engage each clamp.
Connect the connector.
Install the 2 bolts and connect the 2 earth wires.
Connect the connector.
Pass the drain cooler hose through the vehicle securely.
Connect the cooler drain hose firmly to prevent water leaks.
Engage each clamp.
Engage the claw to connect the airbag connector as shown in the illustration.
| *1 | Retainer |
Engage the 2 claws to lock the retainer as shown in the illustration.
| *A | w/ Smart Entry and Start System |
| *1 | Airbag Sensor Assembly |
Engage each clamp.
Connect each connector.
Connect the connector to the airbag sensor assembly as shown in the illustration.
When connecting any airbag connector, take care not to damage the airbag wire harness.
Engage the 3 claws to close the 3 clamps as shown in the illustration.
for 10 Speakers:
Engage the 3 clamps.
3.INSTALL FRONT LOWER PANEL PACKING
Install the 2 front lower panel packings.
55458A
4.INSTALL INSTRUMENT PANEL SAFETY PAD CAP
Install 5 new instrument panel safety pad caps.
| *A | for Driver Side | *B | for Passenger Side |
55307E
5.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Install the screw and 2 nuts.
Install the No. 2 instrument panel brace sub-assembly with the bolt.
Connect the earth wire with the bolt.
Engage each clamp.
Connect the connector.
55306B
6.INSTALL INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
Install the screw and 2 nuts.
Install the instrument panel to cowl brace sub-assembly with the bolt.
Connect the earth wire with the bolt.
Engage each clamp.
Connect each connector.
58861B
7.INSTALL NO. 1 CONSOLE BOX DUCT
Install the No. 1 console box duct with the clip.
87212F
8.INSTALL REAR NO. 2 AIR DUCT
Engage the 2 claws to install the rear No. 2 air duct.
58544A
9.INSTALL FLOOR CARPET BRACKET LH
Engage the 2 guides.
Install the floor carpet bracket LH with the 2 clips.
Engage the guide to install the floor carpet to the original position as shown in the illustration.
77306
10.CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
Engage the guide to connect the fuel lid lock open lever sub-assembly as shown in the illustration.
Install the screw.
87212
11.INSTALL REAR NO. 1 AIR DUCT
Engage the 2 claws to install the rear No. 1 air duct.
58543B
12.INSTALL FLOOR CARPET BRACKET RH
Engage the 2 guides.
Install the floor carpet bracket RH with the 2 clips.
Engage the guide to install the floor carpet to the original position as shown in the illustration.
58521B
13.INSTALL FLOOR CARPET HOOK
Engage the 6 claws to install the 6 floor carpet hooks.
Engage the 6 guides.
85940
14.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)
88650N
15.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
82877
16.INSTALL ECU INTEGRATION BOX RH
82730
17.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)
82730
18.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD)
19.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
20.INSTALL STEERING POST ASSEMBLY
21.INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)
86183D
22.INSTALL AUDIO AMPLIFIER COVER (for 10 Speakers)
23.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
24.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
25.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)
Use the same procedure for the RH side and LH side.
26.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)
Use the same procedure for the RH side and LH side.
88710E
27.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Remove the vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioner tube and accessory assembly.
ND-OIL 8 or equivalent
Install the O-ring to the air conditioner tube and accessory assembly.
Connect the air conditioner tube and accessory assembly.
88704
28.CONNECT SUCTION HOSE SUB-ASSEMBLY
Remove the vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.
ND-OIL 8 or equivalent
Install the O-ring to the suction hose sub-assembly.
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
87245
29.CONNECT HEATER INLET WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to connect the heater inlet water hose.
87246
30.CONNECT HEATER OUTLET WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to connect the heater outlet water hose.
55701J
31.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
32.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
33.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
34.INSPECT FOR COOLANT LEAK
35.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR
36.INSPECT ENGINE COOLANT QUALITY
37. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
38.WARM UP ENGINE
39.INSPECT FOR REFRIGERANT LEAK
40.INITIALIZATION SERVO MOTOR (for Manual Air Conditioning System)
41.INITIALIZATION SERVO MOTOR (for Automatic Air Conditioning System)