Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2015.04–2016.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the ST (Starter) relay drive signal output from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 is input to the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input to the ECM with the engine running, the ECM turns Tr1 on continuously.

*1: w/o smart entry and start system.

*2: w/ smart entry and start system.


WIRING DIAGRAM

A268990E01
0.512,1.318 1.037,1.472 0.525,0.154 10 ST/AM2 1.772,0.604 2.081,0.757 0.31,0.152 10 AM2 2.462,0.604 2.709,0.757 0.247,0.152 10 IG2 1.599,0.435 1.695,0.587 0.095,0.152 10 5 1.025,0.435 1.183,0.587 0.158,0.152 10 *1 3.183,0.435 3.341,0.587 0.158,0.152 10 *1 4.205,0.435 4.363,0.587 0.158,0.152 10 *1 5.116,0.435 5.274,0.587 0.158,0.152 10 *2 2.776,0.435 2.872,0.587 0.095,0.152 10 6 1.302,0.801 1.582,0.953 0.28,0.152 10 I36 1.302,0.955 3.63,1.107 2.328,0.152 10 Ignition or Starter Switch Assembly*1 0.792,2.213 1.442,2.367 0.65,0.154 10 IG2-MAIN 2.22,7.451 2.497,7.6 0.277,0.149 10 N11 2.22,7.605 2.917,7.775 0.697,0.17 10 Fuel Pump 0.679,7.927 1.139,8.097 0.461,0.17 10 Battery 3.083,7.132 4.564,7.302 1.481,0.17 10 No. 1 Integration Relay 3.265,7.973 5.583,8.143 2.318,0.17 10 *1: w/o Smart Entry and Start System 3.265,8.323 5.517,8.493 2.252,0.17 10 *2: w/ Smart Entry and Start System 3.183,3.759 3.813,3.913 0.63,0.154 10 EFI MAIN 3.141,5.071 3.861,5.225 0.72,0.154 10 EFI MAIN2 0.805,3.208 1.844,3.362 1.039,0.154 10 EFI-MAIN NO. 1 0.805,4.899 1.855,5.053 1.05,0.154 10 EFI-MAIN NO. 2 2.405,1.636 2.6,1.788 0.195,0.152 10 1D 2.447,1.454 2.547,1.606 0.1,0.152 10 3 2.405,3.071 2.605,3.223 0.2,0.152 10 1B 2.455,2.889 2.556,3.041 0.1,0.152 10 1 2.405,3.447 2.605,3.6 0.2,0.152 10 1E 2.448,3.269 2.549,3.421 0.1,0.152 10 2 2.405,4.771 2.605,4.924 0.2,0.152 10 1D 2.455,4.589 2.556,4.741 0.1,0.152 10 1 2.405,5.845 2.605,5.997 0.2,0.152 10 1C 2.455,5.666 2.556,5.819 0.1,0.152 10 6 3.368,2.277 3.622,2.429 0.254,0.152 10 IG2 3.28,6.583 3.739,6.735 0.458,0.152 10 C/OPN 4.99,3.447 5.19,3.599 0.2,0.152 10 1C 5.034,3.268 5.134,3.421 0.1,0.152 10 7 5.922,6.727 6.135,6.879 0.213,0.152 10 FC 5.663,6.727 5.838,6.879 0.175,0.152 10 21 5.922,3.447 6.333,3.599 0.411,0.152 10 MREL 5.663,3.361 5.838,3.513 0.175,0.152 10 46 6.388,7.964 6.722,8.117 0.334,0.152 10 ECM 6.037,7.964 6.302,8.117 0.265,0.152 10 A25 3.421,0.656 4.418,0.81 0.997,0.154 10 ECU-IG2 NO. 1 4.435,1.398 4.63,1.55 0.195,0.152 10 1C 4.387,1.198 4.488,1.35 0.1,0.152 10 8 4.99,6.816 5.186,6.968 0.195,0.152 10 1E 5.034,6.634 5.134,6.786 0.1,0.152 10 1 1.898,7.047 1.999,7.199 0.1,0.152 10 4 1.898,7.979 1.999,8.131 0.1,0.152 10 5 1.888,7.759 2.009,7.911 0.121,0.152 10 E 1.888,7.255 2.009,7.407 0.121,0.152 10 B 5.737,0.435 5.837,0.587 0.1,0.152 10 9 5.923,0.519 6.266,0.671 0.343,0.152 10 IG2D 5.579,1.12 5.853,1.272 0.274,0.152 10 A43 5.579,1.288 7.131,1.601 1.552,0.313 10 Certification ECU (Smart Key ECU Assembly)*2 6.539,6.148 6.779,6.3 0.24,0.152 10 Tr1 0.558,6.351 1.181,6.505 0.623,0.154 10 FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.


Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B



A

2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

B

8.READ VALUE USING GTS (STARTER SIGNAL)
2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-1 - A25-21 (FC) Always Below 1 Ω
1E-1 or A25-21 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-6 - N11-4 (B) Always Below 1 Ω
1C-6 or N11-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N11-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

NG

6.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1D-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 1 INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT NO. 1 INTEGRATION RELAY
a.

Inspect the No. 1 integration relay.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

8.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Cranking position ON



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (ENGINE SPEED)

NG

9.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT