Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2015.04–2016.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

w/ smart entry and start system

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).


w/o smart entry and start system

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly to the park/neutral position switch assembly and also flows to terminal STA of the ECM (STA signal).


WIRING DIAGRAM

A266353E19
5.688,3.667 6.063,3.844 0.375,0.177 10 false STA 5.396,3.594 5.583,3.75 0.188,0.156 10 false 22 5.344,3.781 5.615,3.938 0.271,0.156 10 false A25 5.688,0.646 6.063,0.823 0.375,0.177 10 false NEO 5.396,0.594 5.583,0.75 0.188,0.156 10 false 45 5.344,0.781 5.615,0.938 0.271,0.156 10 false A25 5.688,1.406 6.063,1.583 0.375,0.177 10 false NSW 5.396,1.406 5.583,1.563 0.188,0.156 10 false 63 5.344,1.594 5.615,1.75 0.271,0.156 10 false E26 6.073,4.948 6.417,5.115 0.344,0.167 10 false ECM 3.542,2.25 3.646,2.406 0.104,0.156 10 false 9 3.708,2.25 3.813,2.406 0.104,0.156 10 false L 4.375,2.25 4.49,2.406 0.115,0.156 10 false B 4.563,2.25 4.688,2.406 0.125,0.156 10 false 4 3.313,2.563 3.646,2.802 0.333,0.24 10 false E79 3.313,2.729 5.094,3.063 1.781,0.333 10 false Park/Neutral Position Switch Assembly 0.094,0.115 2.667,0.375 2.573,0.26 12 false w/ Smart Entry and Start System: 0.594,3.781 1.125,3.938 0.531,0.156 10 false ST/AM2 1.438,0.781 1.729,0.969 0.292,0.188 10 false NE 1.781,0.667 2.042,0.823 0.26,0.156 10 false 16 1.281,1.583 1.667,1.74 0.385,0.156 10 false STAR 1.781,1.49 1.906,1.646 0.125,0.156 10 false 5 1.375,2.104 1.667,2.26 0.292,0.156 10 false STA 1.781,2 1.906,2.156 0.125,0.156 10 false 7 0.146,2.51 0.458,2.677 0.313,0.167 10 false A43 0.146,2.677 1.958,3.083 1.813,0.406 10 false Certification ECU (Smart key ECU Assembly) 3.271,4.594 3.5,4.75 0.229,0.156 10 false ST 3.01,4.135 3.135,4.292 0.125,0.156 10 false 2 3.01,5.042 3.135,5.198 0.125,0.156 10 false 1 2.573,4.135 2.667,4.292 0.094,0.156 10 false 5 2.573,5.031 2.667,5.188 0.094,0.156 10 false 3 1.792,5.51 2,5.667 0.208,0.156 10 false E9 1.75,5.333 1.844,5.49 0.094,0.156 10 false 1 1.115,5.719 1.24,5.885 0.125,0.167 10 false 1 1.073,5.917 1.292,6.073 0.219,0.156 10 false F2 1.51,6.708 2.156,7.229 0.646,0.521 10 false Starter Assembly 0.74,6.813 1.219,6.979 0.479,0.167 10 false Battery 0.594,4.792 1.219,4.948 0.625,0.156 10 false FL MAIN

A307640E02
0.115,0.104 2.677,0.344 2.563,0.24 12 false w/o Smart Entry and Start System: 1.354,1.177 1.531,1.354 0.177,0.177 10 false 4 1.344,1.604 1.521,1.781 0.177,0.177 10 false 5 2.458,1.594 2.635,1.771 0.177,0.177 10 false 7 2.458,1.177 2.635,1.354 0.177,0.177 10 false 3 1.51,1.177 1.896,1.396 0.385,0.219 10 false AM1 1.51,1.604 1.896,1.823 0.385,0.219 10 false AM2 2.094,1.167 2.479,1.385 0.385,0.219 10 false ST1 2.104,1.604 2.396,1.823 0.292,0.219 10 false ST2 1.469,2.052 1.854,2.271 0.385,0.219 10 false I36 3.542,2.438 3.927,2.656 0.385,0.219 10 false E79 5.344,1.281 5.646,1.469 0.302,0.188 10 false E26 5.396,1.104 5.698,1.292 0.302,0.188 10 false 63 5.333,3.552 5.635,3.74 0.302,0.188 10 false A25 5.698,3.438 6.104,3.625 0.406,0.188 10 false STA 5.396,3.375 5.625,3.563 0.229,0.188 10 false 22 5.688,1.083 6.094,1.271 0.406,0.188 10 false NSW 0.583,2.792 0.906,3.156 0.323,0.365 10 false ST/ AM2 3.292,4.354 3.698,4.542 0.406,0.188 10 false ST 3.5,2.021 3.719,2.219 0.219,0.198 10 false 9 4.552,2.021 4.771,2.219 0.219,0.198 10 false 4 3.708,2.021 3.896,2.229 0.188,0.208 10 false L 4.375,2.021 4.563,2.229 0.188,0.208 10 false B 2.552,3.917 2.719,4.104 0.167,0.188 10 false 5 2.542,4.823 2.708,5.01 0.167,0.188 10 false 3 3.021,3.917 3.188,4.104 0.167,0.188 10 false 2 3.021,4.823 3.188,5.01 0.167,0.188 10 false 1 1.719,5.094 1.885,5.281 0.167,0.188 10 false 1 1.115,5.521 1.281,5.708 0.167,0.188 10 false 1 1.781,5.281 2.021,5.448 0.24,0.167 10 false E9 1.073,5.698 1.292,5.927 0.219,0.229 10 false F2 0.729,6.594 1.281,6.802 0.552,0.208 10 false Battery 1.458,6.49 2.104,6.917 0.646,0.427 10 false Starter Assembly 0.583,4.896 1.281,5.115 0.698,0.219 10 false FL MAIN 1.125,3.677 1.542,3.896 0.417,0.219 10 false ALT 1.104,2.865 1.521,3.083 0.417,0.219 10 false AM1 6.052,4.719 6.458,4.906 0.406,0.188 10 false ECM 1.469,2.208 2.583,2.625 1.115,0.417 10 false Ignition or Starter Switch Assembly 3.542,2.594 4.875,3.021 1.333,0.427 10 false Park/Neutral Position Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

18.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Cranking position ON



Result:
Proceed to
OK
NG



OK

3.INSPECT RELAY (ST RELAY)

NG

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE RELAY (ST RELAY)

4.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 3 - E9-1 Always Below 1 Ω
ST relay terminal 3 or E9-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - F2-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/o smart entry and start system) A
OK (w/ smart entry and start system) B
NG C



A

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

B

11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E79-9 (L) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I36-7 (ST2) - ST relay terminal 5 Always Below 1 Ω
I36-7 (ST2) or ST relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E79-9 (L) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/o smart entry and start system) A
OK (w/ smart entry and start system) B
NG C



A

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

B

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)

C

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I36-3 (ST1) - E79-4 (B) Always Below 1 Ω
I36-3 (ST1) - E26-63 (NSW) Always Below 1 Ω
I36-3 (ST1), E79-4 (B) or E26-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY AND ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY AND ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E79-9 (L) - A25-22 (STA) Always Below 1 Ω
E79-9 (L), ST relay terminal 2 or A25-22 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-5 (STAR) - E79-4 (B) Always Below 1 Ω
A43-5 (STAR) - E26-63 (NSW) Always Below 1 Ω
A43-5 (STAR) or E79-4 (B) or E26-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY, ECM AND CERTIFICATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY, ECM AND CERTIFICATION ECU)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 - E79-9 (L) Always Below 1 Ω
ST relay terminal 2 or E79-9 (L) or A25-22 (STA) or A43-7 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Cranking position ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)