Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD)
RM19V0EQ _54 Brake _014592 BRAKE SYSTEM (OTHER) _0074047 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 47201 4.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 52119A 5.REMOVE FRONT BUMPER COVER

Hide 53293C 6.REMOVE RADIATOR SIDE DEFLECTOR RH

Hide 88710E 7.SEPARATE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.
C239874

Disconnect the pressure sensor connector and separate the clamp.


b.
C239871

Remove the bolt from the hook connector.


c.
C239872

Turn the hook connector and separate the air conditioning tube and accessory assembly from the air conditioning unit.

NOTICE:
·

Do not deform the piping.

·

Do not damage the clamp.




d.
C239877

Remove the bolt and separate the air conditioning tube and accessory assembly from the cooler condenser assembly.

NOTICE:
·

Do not deform the piping.

·

Do not damage the clamp.




e.

Remove the 2 O-rings from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88704 8.SEPARATE SUCTION HOSE SUB-ASSEMBLY

a.
C239179

Disengage the clamp from the brake actuator bracket assembly.


b.
C239876

Separate the clamp with suction hose sub-assembly and air conditioning tube and accessory assembly from the No. 1 brake tube clamp.


c.
C239875

Separate the suction hose sub-assembly from the air conditioning unit.

NOTICE:
·

Do not deform the piping.

·

Do not damage the clamp.




d.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 47371A 9.REMOVE NO. 1 BRAKE TUBE CLAMP

a.
C239890

Disengage the clamp from the brake lines.

NOTICE:

Do not kink or damage the brake lines.



b.

Remove the bolt and No. 1 brake tube clamp from the vehicle body.


Hide 10.REMOVE BRAKE LINE

a.
C239886

Using a union nut wrench, disconnect the 2 brake lines from the brake actuator assembly.


b.
C187545

Remove the 2 clamps to make the 2 brake lines free.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt and dust to enter the brake lines.




Hide 17650 11.REMOVE VACUUM SWITCHING VALVE ASSEMBLY

a.
A254745

Disconnect the union to check valve hose and wire harness clamp.


b.

Disconnect the 2 vacuum hoses and connector.


c.

Remove the bolt and vacuum switching valve assembly.


Hide 44773F 12.DISCONNECT UNION TO CHECK VALVE HOSE

a.
C239878

Slide the clip and disconnect the union to check valve hose from the brake booster assembly.


Hide 47264A 13.REMOVE PUSH ROD PIN

Hide 44610 14.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C239888

Remove the 4 nuts and brake booster assembly from the vehicle body.

NOTICE:

Do not kink or damage the brake lines, air conditioning tube and accessory assembly or suction hose sub-assembly.



Hide 44785 15.REMOVE BRAKE BOOSTER GASKET

a.
C204573

Remove the brake booster gasket from the brake booster assembly.


Hide 47264D 16.REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Loosen the lock nut and remove the brake master cylinder push rod clevis and lock nut.


Hide 44730 17.REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY

a.

Remove the brake vacuum check valve assembly from the brake booster assembly.


Hide 44696 18.REMOVE CHECK VALVE GROMMET

a.

Remove the check valve grommet from the brake booster assembly.