Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _034909 PRE-CRASH SAFETY _0163370 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on pre-crash safety control, the driving support ECU assembly provides warnings to the driver. The driving support ECU assembly does this by sending a request signal to the millimeter wave radar sensor assembly to sound the skid control buzzer.

When the millimeter wave radar sensor assembly detects a malfunction in the skid control buzzer circuit, a malfunction signal is sent to the driving support ECU assembly, and this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit While the engine switch is on (IG), a skid control buzzer circuit malfunction signal is received from the millimeter wave radar sensor assembly for 3 seconds or more.
·

Harness or connector

·

Skid control buzzer

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

B374475E05
0.229,0.677 1.167,1.135 0.938,0.458 10 false From ECU-IG1 NO. 3 Fuse 1.667,0.656 2,0.896 0.333,0.24 10 false IG1 2.073,0.656 2.406,0.896 0.333,0.24 10 false BZ 1.5,0.552 1.833,0.792 0.333,0.24 10 false 2 2.323,0.552 2.656,0.792 0.333,0.24 10 false 1 2.688,0.552 3.021,0.792 0.333,0.24 10 false 10 3.813,0.76 4.146,1 0.333,0.24 10 false 2 3.813,0.281 4.146,0.521 0.333,0.24 10 false 3 2.948,0.656 3.281,0.896 0.333,0.24 10 false BZ 3.385,0.458 3.906,0.698 0.521,0.24 10 false CA1P 4.448,0.448 4.969,0.688 0.521,0.24 10 false CA1P 3.385,0.938 3.906,1.177 0.521,0.24 10 false CA1N 4.448,0.917 4.969,1.156 0.521,0.24 10 false CA1N 4.208,0.292 4.542,0.531 0.333,0.24 10 false 40 4.229,0.76 4.563,1 0.333,0.24 10 false 18 5.396,0.281 5.729,0.521 0.333,0.24 10 false 39 5.406,0.771 5.74,1.01 0.333,0.24 10 false 17 5.833,0.292 6.167,0.531 0.333,0.24 10 false 13 5.844,0.76 6.177,1 0.333,0.24 10 false 26 4.979,0.469 5.5,0.708 0.521,0.24 10 false CA2H 6.063,0.427 6.583,0.667 0.521,0.24 10 false CANH 6.073,0.917 6.594,1.156 0.521,0.24 10 false CANL 5.01,0.927 5.531,1.167 0.521,0.24 10 false CA2L 1.333,1.104 1.854,1.344 0.521,0.24 10 false I185 1.333,1.271 2.604,1.698 1.271,0.427 10 false Skid Control Buzzer 2.781,1.385 4.198,1.813 1.417,0.427 10 false Millimeter Wave Radar Sensor Assembly 2.771,1.229 3.292,1.469 0.521,0.24 10 false A79 4.469,1.396 5.438,1.823 0.969,0.427 10 false Driving Support ECU Assembly 4.469,1.25 4.99,1.49 0.521,0.24 10 false I191 6.354,1.25 6.875,1.49 0.521,0.24 10 false A25 6.354,1.396 6.875,1.635 0.521,0.24 10 false ECM 0.813,2.281 3.375,2.708 2.563,0.427 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

Before performing the inspection, check that DTC U0235, U1002 or U1104 is not output.



PROCEDURE

1.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A4A, U1002, U0235 and U1104 are not output A
DTC C1A4A is output B
DTC C1A4A and U0235 are output C
DTC C1A4A and U1002 are output D
DTC C1A4A and U1104 are output E




A

B

2.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER)

C

D

E

2.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard
PCS Approach Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Approach Alarm Buzzer
50004 220 6
OK:

Skid control buzzer sounds.



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

3.INSPECT SKID CONTROL BUZZER
3.INSPECT SKID CONTROL BUZZER


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - BATTERY)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - BATTERY)
a.
B338290C63
0.542,1.198 0.938,1.458 0.396,0.26 2.396,2 2.146,2 2.146,2 1.875,1.604 true 0.063,0.094 0.323,0.229 0.26,0.135 10 false *a 0.615,1.25 0.969,1.458 0.354,0.208 10 false I185 2.448,1.917 2.896,2.135 0.448,0.219 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the I185 skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I185-2 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
I185-2 (IG1) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the I185 skid control buzzer connector.


b.

Disconnect the A79 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I185-1 (BZ) - A79-10 (BZ) Always Below 1 Ω
I185-1 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCS (PRE-CRASH 2)
7.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B




A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY