Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163371 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P1575  Warning Buzzer Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives an alarm demand signal from the driving support ECU assembly and operates the skid control buzzer. The buzzer sounds to warn that the distance between the vehicle in front and this vehicle is decreasing.

DTC No. Detection Item DTC Detection Condition Trouble Area
P1575 Warning Buzzer Malfunction The ECM receives a buzzer abnormal signal for approximately 0.2 seconds or more while the dynamic radar cruise control is operating.
·

Skid control buzzer

·

Skid control buzzer circuit

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

ECM



WIRING DIAGRAM

A344917E07
0.74,3.344 2.542,3.531 1.802,0.188 10 false : CAN Communication Line 6.25,1.844 6.708,2.042 0.458,0.198 10 false ECM 6.26,1.688 6.719,1.885 0.458,0.198 10 false A25 4.354,1.729 4.813,1.927 0.458,0.198 10 false I191 4.344,1.885 5.333,2.25 0.99,0.365 10 false Driving Support ECU Assembly 2.635,1.708 2.948,1.906 0.313,0.198 10 false A79 2.625,1.854 4.031,2.219 1.406,0.365 10 false Millimeter Wave Radar Sensor Assembly 1.063,1.51 1.521,1.708 0.458,0.198 10 false I185 1.042,1.667 2.292,2.021 1.25,0.354 10 false Skid Control Buzzer 0.052,1.115 0.625,1.646 0.573,0.531 10 false From IG1 NO. 3 Fuse 1.198,1.115 1.656,1.313 0.458,0.198 10 false IG1 1.615,1.104 1.927,1.302 0.313,0.198 10 false BZ 1.052,1.021 1.208,1.219 0.156,0.198 10 false 2 1.844,1.021 2,1.219 0.156,0.198 10 false 1 2.625,1.021 2.938,1.219 0.313,0.198 10 false 10 2.844,1.115 3.156,1.313 0.313,0.198 10 false BZ 3.292,0.896 3.906,1.094 0.615,0.198 10 false CA1P 4.354,0.896 4.969,1.094 0.615,0.198 10 false CA1P 4.354,1.385 4.969,1.583 0.615,0.198 10 false CA1N 3.292,1.375 3.906,1.573 0.615,0.198 10 false CA1N 4.896,0.896 5.51,1.094 0.615,0.198 10 false CA2H 4.896,1.375 5.51,1.573 0.615,0.198 10 false CA2L 5.969,0.885 6.583,1.083 0.615,0.198 10 false CANH 5.958,1.365 6.573,1.563 0.615,0.198 10 false CANL

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



HINT:

If the vehicle ahead in the same lane significantly decreases its speed or another vehicle moves in front of this vehicle, adequate deceleration cannot be applied and the vehicle-to-vehicle distance will shorten. At this time, the system sounds the buzzer and the master warning light blinks to inform the driver. This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more CAN communication system DTCs are stored.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Approach Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
Radar Cruise Approach Alarm Buzzer
50004 220 4
OK:

Skid control buzzer sounds.



f.

Turn the engine switch off.


Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

2.INSPECT SKID CONTROL BUZZER
2.INSPECT SKID CONTROL BUZZER


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SKID CONTROL BUZZER)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SKID CONTROL BUZZER)
a.
B338290C64
0.542,1.198 0.938,1.458 0.396,0.26 2.396,2 2.146,2 2.146,2 1.875,1.604 true 0.063,0.094 0.323,0.229 0.26,0.135 10 false *a 0.615,1.24 0.969,1.448 0.354,0.208 10 false I185 2.448,1.917 2.896,2.135 0.448,0.219 10 false IG1
*a Front view of wire harness connector
(to Skid Control Assembly)


Disconnect the I185 skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I185-2 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
I185-2 (IG1) - Body ground Engine switch off Below 1 V



c.

Reconnect the I185 skid control buzzer connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - BATTERY)

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the I185 skid control buzzer connector.


b.

Disconnect the A79 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I185-1 (BZ) - A79-10 (BZ) Always Below 1 Ω
I185-1 (BZ) or A79-10 (BZ) - Body ground Always 10 kΩ or higher



d.

Reconnect the A79 millimeter wave radar sensor assembly connector.


e.

Reconnect the I185 skid control buzzer connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS (RADAR CRUISE)
6.CHECK FOR DTCS (RADAR CRUISE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 239

d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -SET to activate the dynamic radar cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Powertrain > Radar Cruise > Trouble Codes
50001 239
NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



g.

Turn the engine switch off.


Result:
Result Proceed to
DTC P1575 is not output A
DTC P1575 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

7.REPLACE DRIVING SUPPORT ECU ASSEMBLY
7.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTCS (RADAR CRUISE)
8.CHECK FOR DTCS (RADAR CRUISE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 239

d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -SET to activate the dynamic radar cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Powertrain > Radar Cruise > Trouble Codes
50001 239
NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



Result:
Result Proceed to
DTC P1575 is not output A
DTC P1575 is output B


g.

Turn the engine switch off.



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B