Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163371 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U1102  Lost Communication with Radar Sensor  


DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU assembly transmit the data for general vehicle control and diagnosis function via CAN communication. The driving support ECU assembly determines the curve radius information based on signals from the steering angle sensor and airbag sensor assembly (yaw rate sensor). The driving support ECU assembly transmits the current vehicle speed and curve radius information to the millimeter wave radar sensor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
U1102 Lost Communication with Radar Sensor The ECM detects a communication error signal (from the driving support control ECU assembly to the millimeter wave radar sensor assembly) for approximately 0.15 seconds or more while the dynamic radar cruise control is operating.
·

Millimeter wave radar sensor assembly

·

Millimeter wave radar sensor circuit

·

Driving support ECU assembly



WIRING DIAGRAM

Refer to the wiring diagram for DTC U0235.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>U0235

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication is normal A
CAN communication is malfunctioning B



A

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)

B

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)
a.
A352224C02
1.458,0.229 1.875,0.49 0.417,0.26 2.021,1.135 2.396,0.688 2.396,0.688 2.667,0.688 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.552,0.281 2.01,0.479 0.458,0.198 10 false A79 2.729,0.604 3.188,0.802 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A79 millimeter wave radar sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A79-5 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the A79 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A79 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A79-1 (SGND) - Body ground Always Below 1 Ω



c.

Reconnect the A79 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

4.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
E244596C27
1.552,0.417 1.885,0.635 0.333,0.219 2.469,2.469 1.906,2.469 1.906,2.469 1.771,1.927 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 2.51,2.396 2.708,2.604 0.198,0.208 10 false B 1.594,0.438 1.927,0.604 0.333,0.167 10 false I191
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the I191 driving support ECU assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I191-30 (B) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the I191 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCS (DTC U1102)
7.CHECK FOR DTCS (DTC U1102)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 239

d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -SET to activate the dynamic radar cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Powertrain > Radar Cruise > Trouble Codes
50001 239

g.

Turn the engine switch off.


Result:
Result Proceed to
DTCs are not output A
DTC U1102 is output B



A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY