The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.
The navigation receiver assembly stores this DTC when the difference between the speed information from the navigation antenna assembly and the SPD pulse received from the combination meter assembly becomes large.
A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.
If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C2 | Speed Signal Malfunction | A difference between the GPS speed and SPD pulse is detected. | ·
Navigation receiver assembly ·
Combination meter assembly ·
Harness or connector ·
Junction Connector |
Enter the "System Sensors Check" screen. Refer to Check System Sensors in Operation Check.
While driving the vehicle, compare the value of "Speed" to the reading on the speedometer. Check if these readings are almost equal.
The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.
Vehicle speed displayed on the "System Sensors Check" screen is almost the same as the actual vehicle speed measured using the GTS.
for Anti-lock Brake System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST
for Vehicle Stability Control System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER(for SD)>REMOVAL
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
Check the output waveform.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal I18-3 (+S) and body ground.
Turn the ignition switch to ON.
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | I18-3 (+S) - Body ground |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Wheel being rotated |
The waveform is similar to that shown in the illustration.
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Navigation Receiver Assembly) |
Check the input waveform.
Remove the navigation receiver assembly with the connector(s) still connected.
Connect an oscilloscope to terminal I67-17 (SPD) and body ground.
Turn the ignition switch to ON.
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | I67-17 (SPD) - Body ground |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Wheel being rotated |
The waveform is similar to that shown in the illustration.
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER(for SD)>REMOVAL
NG
Disconnect the I67 navigation receiver assembly connector.
Disconnect the I181 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-17 (SPD) - I181-17 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I18 combination meter assembly connector.
Disconnect the I181 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I18-3 (+S) - I181-18 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG