Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P2004  Intake Manifold Runner Control Stuck Open (Bank 1)  P2006  Intake Manifold Runner Control Stuck Closed (Bank 1)  


DESCRIPTION

HINT:

This DTC is applicable to models w/ tumble control valve.


The Tumble Control Valve (TCV) is built into the intake manifold. The intake air control valve actuator (for tumble control valve) is composed of a position sensor and a DC motor. The DC motor opens and closes the tumble control valve in response to signals from the ECM. The position sensor detects the opening angle of the tumble control valve.

When the tumble control valve is closed, the intake air tumble flow intensifies and negative pressure is generated between the tumble control valve and intake valve which atomizes the fuel. Combustion is enhanced and exhaust gas emissions are reduced at low temperatures.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2004 Intake Manifold Runner Control Stuck Open (Bank 1) The tumble control valve opening angle is 17 deg. or more after requesting the tumble control valve to fully close (2 trip detection logic).
·

Open or short in intake air control valve actuator (for tumble control valve) circuit

·

Intake air control valve actuator (for tumble control valve)

·

Intake manifold

·

ECM


Comes on DTC stored
P2006 Intake Manifold Runner Control Stuck Closed (Bank 1) The tumble control valve opening angle is less than 35 deg. after requesting the tumble control valve to fully open (2 trip detection logic).
·

Open or short in intake air control valve actuator (for tumble control valve) circuit

·

Intake air control valve actuator (for tumble control valve)

·

Intake manifold

·

ECM


Comes on DTC stored

HINT:

When P2004 and/or P2006 is output, use the GTS to confirm Intake Air Control Position while performing Control the IAC Duty Ratio of the Active Test.

Reference (Normal condition: When Engine Warmed Up)
Control the IAC Duty Ratio Operation Intake Air Control Position
100% Approximately 70 deg.
0% Approximately 70 deg.
-100% Approximately 2 deg.


MONITOR DESCRIPTION

When the ECM has requested a tumble control valve close operation but the actual tumble control valve opening angle is 17 deg. or more for 10 seconds, DTC P2004 is stored. When the ECM has requested a tumble control valve open operation but the actual tumble control valve opening angle is less than 35 deg. for 10 seconds, DTC P2006 is stored.

MONITOR STRATEGY

Required Sensors/Components (Main) Tumble control valve
Required Sensors/Components (Related) Intake air temperature sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A198851E07
3.406,2.948 4.438,3.396 false 4.521,2.948 4.438,3.396 false 5.615,2.948 4.438,3.396 false 0.677,2.417 1.844,2.688 1.167,0.271 10 Ignition Switch ON 2.427,2.25 2.625,2.448 0.198,0.198 10 [A] 3.417,2.25 3.615,2.448 0.198,0.198 10 [B] 4.417,2.25 4.615,2.448 0.198,0.198 10 [B] 5.406,2.25 5.604,2.448 0.198,0.198 10 [B] 5.667,3.229 5.885,3.406 0.219,0.177 10 [C] 3.646,3.427 5.313,3.583 1.667,0.156 10 Approximately 10 seconds

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on [A].

7.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

HINT:
·

Check for DTC P2004 at a engine coolant temperature of 30°C (86°F) or less.

·

Check for DTC P2006 at a engine coolant temperature of 80°C (176°F) or higher.



8.

Turn the ignition switch off.

9.

Turn the ignition switch to ON, wait approximately 10 seconds, and then turn the ignition switch off. Repeat this procedure 3 times [B].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P2004 or P2006.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255379E15
1.542,0.927 1.875,1.104 0.333,0.177 10 false VDD 1.958,0.833 2.063,0.979 0.104,0.146 10 false 3 1.542,1.521 1.875,1.698 0.333,0.177 10 false OUT 1.958,1.427 2.063,1.573 0.104,0.146 10 false 1 1.542,2.125 1.875,2.302 0.333,0.177 10 false GND 1.958,2.031 2.063,2.177 0.104,0.146 10 false 2 1.635,3.125 1.875,3.302 0.24,0.177 10 false M+ 1.958,3.031 2.063,3.177 0.104,0.146 10 false 5 1.646,3.729 1.875,3.906 0.229,0.177 10 false M- 1.958,3.646 2.063,3.792 0.104,0.146 10 false 4 0.406,4.479 0.635,4.646 0.229,0.167 10 false Y2 0.406,4.625 4.313,5.156 3.906,0.531 10 false Intake Air Control Valve Actuator (for Tumble Control Valve) 4.385,0.823 4.656,0.99 0.271,0.167 10 false 130 4.75,0.823 5.115,0.979 0.365,0.156 10 false VCIA 4.385,1.438 4.656,1.604 0.271,0.167 10 false 131 4.75,1.427 5.115,1.583 0.365,0.156 10 false IAC1 4.385,2.031 4.656,2.198 0.271,0.167 10 false 129 4.75,2.042 5.115,2.198 0.365,0.156 10 false EIA1 4.469,3.031 4.646,3.198 0.177,0.167 10 false 22 4.75,3.021 5.115,3.177 0.365,0.156 10 false IA1+ 4.469,3.646 4.656,3.813 0.188,0.167 10 false 21 4.75,3.635 5.115,3.792 0.365,0.156 10 false IA1- 5.479,4.5 5.76,4.646 0.281,0.146 10 false E26 5.479,4.646 5.833,4.802 0.354,0.156 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2004 OR P2006)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P2004 or P2006 is output A
DTC P2004 or P2006 and other DTCs are output B


HINT:

If any DTCs other than P2004 or P2006 are output, troubleshoot those DTCs first.




A

2.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

B

2.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)
a.

Inspect the intake air control valve actuator (for tumble control valve).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE MANIFOLD (TUMBLE CONTROL VALVE OPERATION)

NG

REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

3.INSPECT INTAKE MANIFOLD (TUMBLE CONTROL VALVE OPERATION)
a.

Inspect the intake manifold for the tumble control valve operation.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the intake manifold.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM)
a.

Disconnect the intake air control valve actuator connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y2-4 (M-) - E26-21 (IA1-) Always Below 1 Ω
Y2-5 (M+) - E26-22 (IA1+) Always Below 1 Ω
Y2-4 (M-) or E26-21 (IA1-) - Body ground and other terminals Always 10 kΩ or higher
Y2-5 (M+) or E26-22 (IA1+) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2004 OR P2006)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2004 OR P2006)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P2004 or P2006 is output A
DTC is not output B



A

B