Home › Engine / Hybrid System › 2AR-FE INTAKE / EXHAUST › INTAKE SYSTEM › from 2016.05
RM19V0EQ _51 Engine / Hybrid System _014577 2AR-FE INTAKE / EXHAUST _0073947 INTAKE SYSTEM G

2AR-FE INTAKE / EXHAUST  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INTAKE SYSTEM

HINT:

Perform Inspection After Repair after repairing air leaks in the intake system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Check that there are no vacuum leaks at the points shown in the illustration.

A264733C01
0.198,0.208 0.865,0.563 0.667,0.354 12 false *A
*A for RHD - -


A264734C01
0.188,0.198 0.854,0.583 0.667,0.385 12 false *A
*A for LHD - -



Hide 2.INSPECT INTAKE AIR CONTROL VALVE (for ACIS)

a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine.


d.
A197999

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Intake Control
50004 234 3

e.

When "Activate the VSV for Intake Control" is turned on, check that the actuator rod operates.

If the operation is not as specified, inspect the intake air control valve (for ACIS), vacuum tank and No. 1 check valve.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>INSPECTION


f.

When "Activate the VSV for Intake Control" is turned off, check that the actuator rod returns to its original position.

If the operation is not as specified, inspect the intake air control valve (for ACIS) and vacuum hose.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>INSPECTION


Hide 3.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (for TCV)

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the IAC Duty Ratio.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the IAC Duty Ratio
Data List Display
Intake Air Control Position
50004 234 150 161
i.

Set the duty ratio to 60% or -60% for 1 to 3 seconds, and then return the duty ratio to 0%. Check "Intake Air Control Position" in the Data List.

Specified Condition:
Condition (Active Test) Specified Condition (Data List)
Control the IAC Duty Ratio set to 60% Intake Air Control Position 35° or more
Control the IAC Duty Ratio set to -60% Intake Air Control Position 17° or less


NOTICE:
·

Supply power to the intake air control valve actuator (for TCV) for 1 to 3 seconds.

·

If power is supplied to the intake air control valve actuator (for TCV) for less than 1 second, the gear of the tumble control valve (TCV) does not reach the stopper and the value in the Data List may be incorrect.

·

If power is supplied to the intake air control valve actuator (for TCV) for more than 3 seconds, the motor may be damaged.

·

Do not perform this inspection more than 2 times consecutively.



HINT:

The standard duty ratio for inspections is 60% or -60%. However, if the value in the Data List is not as specified, set the duty ratio to 100% or -100% for 1 to 3 seconds, and check the value in the Data List again.


Specified Condition:
Condition (Active Test) Specified Condition (Data List)
Control the IAC Duty Ratio set to 100% Intake Air Control Position 70° or more
Control the IAC Duty Ratio set to -100% Intake Air Control Position 2° or less




e.

When the result is not as specified during the Active Test, perform the following procedure.

i.
A197127C03
1.625,4.385 1.531,4.385 1.531,4.385 1.375,4.104 false 0.969,4.385 1.083,4.385 1.083,4.385 1.208,4.104 false 0.521,4.292 0.99,4.479 0.469,0.188 10 false 5 (M+) 1.719,4.302 2.167,4.49 0.448,0.188 10 false 4 (M-) 0.719,0.26 0.948,0.49 0.229,0.229 10 false *a 2.49,0.24 2.771,0.448 0.281,0.208 10 false *b 0.458,3.458 0.771,3.656 0.313,0.198 10 false *c
*a Closed
*b Open
*c Component without harness connected
(Intake Air Control Valve Actuator (for TCV))


Remove the intake manifold.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL

HINT:

When the intake manifold is removed, the 4 tumble control valves (TCV) are half open.



ii.

Check that the 4 tumble control valves (TCV) move when the battery is connected to the terminals of the intake air control valve actuator (for TCV).

Standard:
Tester Connection Specified Condition
Positive (+) battery voltage applied to terminal 4 (M-), and negative (-) battery voltage applied to terminal 5 (M+) Open → Closed
Positive (+) battery voltage applied to terminal 5 (M+), and negative (-) battery voltage applied to terminal 4 (M-) Closed → Open


NOTICE:
·

Apply battery voltage for 1 to 3 seconds.

·

If battery voltage is applied for more than 3 seconds, the intake air control valve actuator (for TCV) may be damaged.

·

If the positive (+) and negative (-) battery leads contact the sensor terminals, the intake air control valve actuator (for TCV) may be damaged.




iii.

If the results are not as specified, perform the following inspections:

1.
A199792

Check that the 4 tumble control valves (TCV) are not cracked or deformed.

2.
A199874

Remove the intake air control valve actuator (for TCV) and check that the 4 tumble control valves (TCV) move smoothly.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>REMOVAL

If there are no problems with the 4 tumble control valves (TCV), inspect the intake air control valve actuator (for TCV).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>INSPECTION




Hide 4.PERFORM INITIALIZATION

a.

Perform Inspection After Repair after repairing vacuum leaks in the intake system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION