DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) |
DTC P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0011 P0021 | Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic). |
|
| P0012 P0022 | Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic). |
| Required Sensors/Components (Main) | Camshaft timing oil control valve assembly (for intake camshaft) Camshaft timing gear assembly |
| Required Sensors/Components (Related) | Crankshaft position sensor VVT sensor Engine coolant temperature sensor |
| Frequency of Operation | Continuous |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Abnormal Bank | Timing Over Advanced (Valve timing is out of specified range) | Timing Over Retarded (Valve timing is out of specified range) |
| Bank 1 | P0011 | P0012 |
| Bank 2 | P0021 | P0022 |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0011, P0012, P0021 or P0022 is output | A |
| DTC P0011, P0012, P0021 or P0022 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Turn the A/C switch on.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve assembly (for intake camshaft) using the tester.
| Tester Operation | Engine Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0011, P0012, P0021 or P0022 is output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
![]() |
Remove the cylinder head cover sub-assemblies RH and LH (Click here).
Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.
| *1 | Timing Mark |
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for intake camshaft) (Click here).
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE |
![]() |
Remove the oil pipe or No. 1 oil pipe (Click here).
Remove the oil control valve filter RH or oil control valve filter LH.
Check that the oil control valve filter and oil pipe are not clogged.
| *1 | Bank 1 |
| *2 | Bank 2 |
| *a | Oil Pipe |
| *b | No. 1 Oil Pipe |
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
Replace the camshaft timing gear assembly (bank 1 or bank 2) (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0011, P0012, P0021 or P0022 is output | B |
|
| ||||
| A | ||
| ||