Home › Engine / Hybrid System · 1AZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

for Preparation Click here


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
  1. A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).
  2. An emission deterioration misfire occurs (MIL illuminates).
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector assembly
  6. Fuel pressure
  7. Mass air flow meter sub-assembly
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connections
  14. Intake system
  15. ECM
P0301
P0302
P0303
P0304
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
  1. A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).
  2. An emission deterioration misfire occurs (MIL illuminates).
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. An excessive number of misfires (50 misfires or more per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
  1. At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.

MONITOR STRATEGY


Required Sensors/Components (Main)
Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature
Intake air temperature sensor
Mass air flow meter sub-assembly
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Misfire 
Intake air temperature
Higher than -10°C (14°F)
Either of the following conditions is met
(a) or (b)
(a) Engine coolant temperature at engine start
Higher than -7°C (19°F)
(b) Engine coolant temperature
Higher than 20°C (68°F)

Monitor Period of Emission-related Misfire 
Duration
1000 crankshaft revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks) 
Duration
200 crankshaft revolutions x 3

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester on.
  4. Record the DTC(s) and freeze frame data.
  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  6. Using the tester, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

    Engine speed
    Duration
    Idling
    8.0 minutes or more
    1000
    4.5 minutes or more
    2000
    2.5 minutes or more
    3000
    1.5 minutes or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.

  10. Record the DTC(s), freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 30 seconds.
  12. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

WIRING DIAGRAM

Refer to DTC P0102 .
Refer to Fuel Injector Circuit .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
    1. There was insufficient fuel in the tank.
    2. Improper fuel was used.
    3. The spark plugs have been contaminated.
    4. The problem requires further diagnosis.
  5. After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
  7. When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (15% or higher).
  8. When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires have occurred only while warming up the engine.
  9. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0300, P0301, P0302, P0303 and/or P0304 are output
    A
    DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections (Click here).

    OK:
    PCV valve and hose are correctly connected and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING INTELLIGENT TESTER (CYLINDER MISFIRE COUNT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.

  1. Start the engine and allow the engine to idle.

  1. Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the tester. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Intelligent Tester (Misfire RPM and Misfire Load)" procedures above [A].

  1. Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the tester [B].

    Result 
    Result
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

HINT:
  1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
  2. If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
  3. If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 16
A


5.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG (Click here)
OK


6.CHECK FOR SPARK (SPARK TEST)
  1. Perform a spark test .

    HINT:
    If the result of the spark test is normal, proceed to the next step.


NEXT


7.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


8.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)


    A194154E77
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E83-108 (#10) - E83-45 (E01)
    Ignition switch ON
    11 to 14 V
    E83-107 (#20) - E83-45 (E01)
    Ignition switch ON
    11 to 14 V
    E83-106 (#30) - E83-45 (E01)
    Ignition switch ON
    11 to 14 V
    E83-105 (#40) - E83-45 (E01)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


9.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


10.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER
  1. Check the valve clearance .



NG
ADJUST VALVE CLEARANCE
OK


11.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


12.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 32
OK


13.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:

    Tester Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


14.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:

    Tester Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 3000 rpm
    Between 8 gm/sec and 22 gm/sec



NG
Go to step 27
OK


15.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
A146275E03
  1. Remove the cylinder head cover sub-assembly.

  1. Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are aligned with the front marks located on the No. 1 and No. 2 bearing caps as shown in the illustration.

    HINT:
    If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

    OK:
    Timing marks on camshaft timing gear assembly and camshaft timing sprocket are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark
    *2
    Front Mark
    *3
    Groove



OK
Go to step 27

NG
ADJUST VALVE TIMING (Click here)

16.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


17.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 32
OK


18.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:

    Tester Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


19.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:

    Tester Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 3000 rpm
    Between 8 gm/sec and 22 gm/sec



NG
Go to step 27
OK


20.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
A146275E03
  1. Remove the cylinder head cover sub-assembly.

  1. Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are aligned with the front marks located on the No. 1 and No. 2 bearing caps as shown in the illustration.

    HINT:
    If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

    OK:
    Timing marks on camshaft timing gear assembly and camshaft timing sprocket are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark
    *2
    Front Mark
    *3
    Groove



NG
ADJUST VALVE TIMING (Click here)
OK


21.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG (Click here)
OK


22.CHECK FOR SPARK (SPARK TEST)
  1. Perform a spark test .

    HINT:
    If the result of the spark test is normal, proceed to the next step.


NEXT


23.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


24.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)


    A194154E77
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E83-108 (#10) - E83-45 (E01)
    Ignition switch ON
    11 to 14 V
    E83-107 (#20) - E83-45 (E01)
    Ignition switch ON
    11 to 14 V
    E83-106 (#30) - E83-45 (E01)
    Ignition switch ON
    11 to 14 V
    E83-105 (#40) - E83-45 (E01)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


25.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


26.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER
  1. Check the valve clearance .



NG
ADJUST VALVE CLEARANCE
OK


27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


28.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303 or P0304.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL
    (DTC P0300, P0301, P0302, P0303 or P0304 is output)
    A
    NORMAL
    (DTC is not output)
    B



B
END
A


29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E14-5 (VG) - E83-118 (VG)
    Always
    Below 1 Ω
    E14-4 (E2G) - E83-116 (E2G)
    Always
    Below 1 Ω
    E14-5 (VG) or E83-118 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


30.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
  1. Replace the mass air flow meter sub-assembly (Click here).

    HINT:
    If the results of the inspections performed in steps 14 and 19 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.


NEXT


31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303 or P0304.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL
    (DTC is not output)
    A
    ABNORMAL
    (DTC P0300, P0301, P0302, P0303 or P0304 is output)
    B



B
REPLACE ECM (Click here)
A

END 

32.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)