DTC P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0015 Camshaft Position "B" - Timing Over-Retarded (Bank 1) |
DTC P0024 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0025 Camshaft Position "B" - Timing Over-Retarded (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0014 P0024 | Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic). |
|
| P0015 P0025 | Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic). |
| Required Sensors/Components (Main) | Camshaft timing oil control valve assembly (for exhaust camshaft) Camshaft timing exhaust gear assembly |
| Required Sensors/Components (Related) | Crankshaft position sensor VVT sensor Engine coolant temperature sensor |
| Frequency of Operation | Continuous |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Abnormal Bank | Timing Over Advanced (Valve timing is out of specified range) | Timing Over Retarded (Valve timing is out of specified range) |
| Bank 1 | P0014 | P0015 |
| Bank 2 | P0024 | P0025 |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0014, P0015, P0024 or P0025 is output | A |
| DTC P0014, P0015, P0024 or P0025 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Turn the A/C switch on.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust camshaft) using the tester.
| Tester Operation | Engine Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0014, P0015, P0024 or P0025 is output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
![]() |
Remove the cylinder head cover sub-assemblies RH and LH (Click here).
Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.
| *1 | Timing Mark |
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (Click here).
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE |
![]() |
Remove the oil pipe or No. 1 oil pipe (Click here).
Remove the oil control valve filter RH or oil control valve filter LH.
Check that the oil control valve filter and oil pipe are not clogged.
| *1 | Bank 1 |
| *2 | Bank 2 |
| *a | Oil Pipe |
| *b | No. 1 Oil Pipe |
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Replace the camshaft timing exhaust gear assembly (bank 1 or bank 2) (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0014, P0015, P0024 or P0025 is output | B |
|
| ||||
| A | ||
| ||