Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here


HINT:
Use the following procedure to troubleshoot the engine immobiliser system.
*: Use the intelligent tester.



1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS

      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      3. The following 5 items are important points in the problem analysis:


      What
      Vehicle model, system name
      When
      Date, time, occurrence frequency
      Where
      Road conditions
      Under what conditions?
      Driving conditions, weather conditions
      How did it happen?
      Problem symptoms

    NEXT


    3.INSPECT BATTERY VOLTAGE
    1. Measure the battery voltage.

      Standard Voltage:
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


    NEXT


    4.CRANK ENGINE FOR MORE THAN 10 SECONDS

      NEXT


      5.CHECK FOR DTCS (ENGINE IMMOBILISER SYSTEM)*
      1. Check for DTCs and note any codes that are output.

      2. Clear the DTCs (Click here).

      3. Recheck for DTCs. Based on the DTCs output above, try to duplicate the engine immobiliser system DTC by simulating the symptoms indicated by the DTCs.

        Result:
        Result
        Proceed to
        No DTCs are output
        A
        Engine immobiliser system DTC is output
        B



      B.
      GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
      A


      6.CHECK FOR DTCS (SFI SYSTEM)*
      1. Clear the DTCs (Click here).

      2. Recheck for DTCs.

        HINT:
        The DTCs for the engine immobiliser system are specified below. If other DTCs are output, check the DTC chart for the SFI system.

        Result:
        Result
        Proceed to
        No DTCs are output
        A
        Engine immobiliser system DTC is output (DTC B2799, B279A or B279C)
        B
        SFI system DTC is output (except DTC B2799, B279A and B279C) (for 2AR-FE)
        C
        SFI system DTC is output (except DTC B2799, B279A and B279C) (for 1AZ-FE)
        D



      B.
      GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

      C.
      GO TO SFI SYSTEM (Click here)

      D.
      GO TO SFI SYSTEM (Click here)
      A


      7.READ VALUE USING INTELLIGENT TESTER*
      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Immobiliser / Data List.

      5. Read the Data List according to the display on the intelligent tester.

        Immobiliser (Transponder Key ECU Assembly) 
        Tester Display
        Measurement Item/Range
        Normal Condition
        Diagnostic Note
        Key SW
        Unlock warning switch signal/ON or OFF
        ON: Key in ignition key cylinder
        OFF: No key in ignition key cylinder
        -

        OK:
        On the intelligent tester screen, the item changes between ON and OFF according to the chart above.



      NG.
      GO TO DTC B2780 (Click here)
      OK


      8.PROBLEM SYMPTOMS TABLE
      1. Refer to Problem Symptoms Table (Click here).

        Result:
        Result
        Proceed to
        Fault is not listed in Problem Symptoms Table
        A
        Fault is listed in Problem Symptoms Table
        B



      B.
      Go to step 10
      A


      9.OVERALL ANALYSIS AND TROUBLESHOOTING*
      1. Data List / Active Test (Click here)

      2. Terminals of ECU (Click here)


      NEXT


      10.REPAIR OR REPLACE

        NEXT


        11.CONFIRMATION TEST

          NEXT

          END