Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR AXLE CARRIER

REAR AXLE CARRIER > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY
  1. Install the rear axle carrier sub-assembly to the rear shock absorber assembly with the 2 bolts and 2 nuts.

    Torque:
    180 N*m{ 1835 kgf*cm , 133 ft.*lbf }

    NOTICE:
    While keeping the bolts from rotating, tighten the nuts.



2. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY
  1. Temporarily tighten rear No. 1 suspension arm assembly (outer side) to the rear axle carrier sub-assembly with the bolt and nut.

    NOTICE:
    When temporarily tightening the bolt, keep the nut from rotating.

    HINT:
    Insert the bolt from the front of the vehicle.



3. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY
  1. Temporarily tighten rear No. 2 suspension arm assembly (outer side) to the rear axle carrier sub-assembly with the bolt and nut.

    NOTICE:
    When temporarily tightening the bolt, keep the nut from rotating.

    HINT:
    Insert the bolt from the rear of the vehicle.



4. TEMPORARILY TIGHTEN REAR STRUT ROD ASSEMBLY
  1. Temporarily tighten rear strut rod assembly (rear side) to the rear axle carrier sub-assembly with the bolt and nut.

    NOTICE:
    When temporarily tightening the bolt, keep the nut from rotating.

    HINT:
    Insert the bolt from the inside of the vehicle.



5. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY
  1. Install the rear axle hub and bearing assembly and parking brake assembly to the rear axle carrier sub-assembly with the 4 bolts.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



6. CONNECT SKID CONTROL SENSOR WIRE
  1. Connect the connector to the rear speed sensor.



7. INSTALL REAR DISC


    C238505E01
  1. Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



8. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the parking brake shoe adjusting hole plug.



9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
  1. Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    62 N*m{ 630 kgf*cm , 46 ft.*lbf }

  1. Install the rear flexible hose to the rear shock absorber assembly with the bolt.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }



10. STABILIZE SUSPENSION


    C240578E02
  1. Jack up the rear axle carrier sub-assembly, placing a wooden block under it to avoid damage. Apply load to the suspension so that the installed bolt of the rear No. 1 suspension arm assembly (inner side) is horizontally aligned with the center of the rear axle hub.
    Text in Illustration 
    *1
    Wooden Block

    CAUTION:
    Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

    NOTICE:
    1. When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.
    2. Make sure to perform this operation with the vehicle kept as low as possible.



11. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY


    C144134
  1. Fully tighten the bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    NOTICE:
    Since a stopper nut is used, fully tighten the bolt.



12. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY


    C167791
  1. Fully tighten the bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    NOTICE:
    Since a stopper nut is used, fully tighten the bolt.



13. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY


    C132476
  1. Fully tighten the bolt

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

    NOTICE:
    Since a stopper nut is used, fully tighten the bolt.



14. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)
(Click here)

HINT:
It is necessary to install the rear height control sensor sub-assembly when installing the rear No. 2 suspension arm assembly RH.



15. ADJUST PARKING BRAKE
(Click here)


16. INSTALL REAR WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



17. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(Click here)


18. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL (w/ Height Control Sensor)
  1. for AFS (Adaptive Front-Lighting System) : (Click here)
  2. for Automatic Headlight Beam Level Control System: (Click here)


19. INSPECT AND ADJUST HEADLIGHT AIMING (w/ Height Control Sensor)
(Click here)


20. CHECK FOR SPEED SENSOR SIGNAL
(Click here)