Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P1603    Engine Stall History

DTC    P1605    Rough Idling

for Preparation Click here


DESCRIPTION

  1. P1603
After starting the engine, this DTC is stored when the engine stops without the engine switch being operated.
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

DTC No.
DTC Detection Condition
Trouble Area
P1603
After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic).
  1. Air leak in intake system
  2. Purge VSV
  3. Brake booster hose not connected properly
  4. Mass air flow meter sub-assembly
  5. Engine coolant temperature sensor
  6. Wire harness or connector
  7. Air fuel ratio sensor
  8. Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly)
  9. Fuel pump
  10. Fuel pump control system
  11. Fuel line (fuel filter, pipes and hoses)
  12. Throttle with motor body assembly
  13. Camshaft timing oil control valve assembly
  14. Air conditioning system
  15. Power steering system
  16. Electrical load signal system
  17. A/T system
  18. Park/Neutral position switch assembly
  19. Thermostat
  20. ECM
  1. P1605
This DTC is stored if the engine speed drops below the set speed.
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No.
DTC Detection Condition
Trouble Area
P1605
After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic).
  1. Air leak in intake system
  2. Purge VSV
  3. Brake booster hose not connected properly
  4. Mass air flow meter sub-assembly
  5. Engine coolant temperature sensor
  6. Wire harness or connector
  7. Air fuel ratio sensor
  8. Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly)
  9. Fuel pump
  10. Fuel pump control system
  11. Fuel line (fuel filter, pipes and hoses)
  12. Throttle with motor body assembly
  13. Camshaft timing oil control valve assembly
  14. Knock control sensor
  15. Ignition coil assembly (No. 1 to No. 6 cylinder)
  16. Fuel injector assembly
  17. Spark plug(s)
  18. Air conditioning system
  19. Power steering system
  20. Electrical load signal system
  21. A/T system
  22. Park/Neutral position switch assembly
  23. ECM

Reference waveforms showing a normal cold engine start

A258932


Reference waveforms showing a normal warm engine start

A258933


Reference values when there is an air leak in the intake system during rough idling

Freeze Frame Data P1605 Rough Idling 
Parameter
-3
-2
-1
0
1
Unit
Engine Speed
647
649
586
378
182
rpm
Calculate Load
26.2
26.2
29.1
42.6
58.6
%
Vehicle Load
11.7
11.7
12.1
48.7
61.2
%
MAF
2.87
2.87
2.87
6.23
3.04
gm/sec
Atmosphere Pressure
0
0
0
0
0
kPa
Coolant Temp
187
187
187
187
187
F
Intake Air
109
109
109
109
109
F
Battery Voltage
13.515
13.515
13.264
12.892
12.792
V
Throttle Sensor Volt %
14.5
14.5
14.5
16.8
17.2
%
Throttl Sensor #2 Volt %
46.2
46.2
46.2
48.4
49.2
%
Throttle Sensor Position
0.0
0.0
0.0
0.0
0.0
%
Throttle Motor DUTY
14.5
14.5
14.5
17.2
17.2
%
Injector (Port)
2159
2161
2148
2190
2190
μs
Injection Volum (Cylinder 1)
0.093
0.093
0.093
0.095
0.095
ml
Fuel Pump Duty
58.6
58.6
58.6
58.6
58.6
%
EVAP (Purge) VSV
13.3
13.3
13.3
13.3
13.3
%
Evap Purge Flow
2.9
2.9
2.9
3.2
3.2
%
Purge Density Learn Value
0.891
0.891
0.891
0.891
0.891

EVAP Purge VSV
OFF
OFF
OFF
OFF
OFF

Purge Cut VSV Duty
8.5
8.5
8.5
8.5
8.5
%
Target Air-Fuel Ratio
0.998
0.998
0.998
0.998
0.998

AF Lambda B1S1
0.999
0.997
1.001
1.038
1.118

AF Lambda B2S1
0.997
0.994
0.999
1.036
1.112

AFS Voltage B1S1
3.258
3.242
3.284
3.521
3.715
V
AFS Voltage B2S1
3.251
3.306
3.324
3.497
3.689
V
O2S B1S2
0.740
0.740
0.740
0.740
0.740
V
O2S B2S2
0.760
0.760
0.760
0.760
0.760
V
Short FT #1
-1.563
-1.563
-1.563
-1.563
-1.563
%
Long FT #1
6.250
6.250
6.250
6.250
6.250
%
Total FT #1
0.054
0.054
0.054
0.054
0.054

Sort FT #2
-0.782
-0.782
-0.782
-0.782
-0.782
%
Long FT #2
7.031
7.031
7.031
7.031
7.031
%
Total FT #2
0.062
0.062
0.062
0.062
0.062

Fuel System Status #1
CL
CL
CL
CL
CL

Fuel System Status #2
CL
CL
CL
CL
CL

IGN Advance
22.0
22.0
22.5
23.5
23.5
deg
Knock Feedback Value
-1.5
-1.5
-1.5
-1.5
-1.5
°CA
Knock Correct Learn Value
17.0
17.0
17.0
17.0
17.0
°CA
Starter Signal
Close
Close
Close
Close
Close


WIRING DIAGRAM

Refer to DTC P0351 for the ignition coil circuit .
Refer to DTC P0443 for the purge VSV circuit .
Refer to DTC P2195 for the air fuel ratio sensor circuit .
Refer to Fuel Pump Control Circuit .
Refer to Fuel Injector Circuit .

INSPECTION PROCEDURE

HINT:
  1. In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
    As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
  2. If any other DTCs are output, perform troubleshooting for those DTCs first.
  3. Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

    Symptom
    Suspected Area
    Engine vibration occurs and engine stops
    Air fuel ratio abnormal
    Engine stops with no engine vibration
    Ignition system, injection stoppage, high load from external parts
    Engine can be started with accelerator pedal depressed
    Insufficient air volume
    Rough idling after engine started
    Air fuel ratio abnormal, abnormal combustion
  4. Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
  5. When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
  6. When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. (The ECM stores DTC P1605 first. Therefore, the 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.)
  7. When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
  8. Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
  9. Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.
  10. When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.

Inspection flow:
Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.

  1. P1603:

A224366E03

1:
  1. If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air fuel ratio, etc.
  2. If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.
2:
  1. If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.
  2. If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
3:
  1. If the air fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
  2. If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Vehicle State
Engine Speed
Suspected Area
Primary Parts to Inspect
Procedure
Idling or decelerating
Slowly decreases and engine stalls
Air fuel ratio abnormal
Air suction
  1. Intake system connections
  2. Purge VSV system
  3. Brake booster assembly
3 to 6
Sensor malfunction (value from sensor too lean)
  1. Mass air flow meter sub-assembly
  2. Engine coolant temperature sensor
  3. Air fuel ratio sensor system
7 to 16
Sensor malfunction (value from sensor too rich)
25 to 34
Fuel supply problem
  1. Fuel pump control system
  2. Purge VSV system
  3. Fuel line
  4. ECM
17 to 24
Intake air volume insufficient
ISC flow rate
  1. Throttle with motor body assembly (ISC valve)
35 to 37
Excessive valve overlap
  1. Camshaft timing oil control valve assembly
38, 39
Ignition timing incorrect
Does not operate as expected
  1. Engine coolant temperature sensor
  2. Knock control sensor
  3. Mass air flow meter sub-assembly
40 to 42
Rapidly decreases and engine stalls
Ignition and injection stops (electrical system malfunction)
Power temporarily cut
  1. Power supply circuit (Fuel injector assembly, ignition coil assembly)
43, 44
External part malfunctioning
Increase in load
  1. Air conditioning system
  2. Electrical load signal system
  3. Power steering system
  4. A/T system
  5. Park/Neutral position switch assembly
47 to 49
Accelerating
-
Crankshaft position sensor, VVT sensor malfunction
Power temporarily cut
  1. Check DTCs
1
Mass air flow meter sub-assembly
Foreign matter adhesion
  1. Mass air flow meter sub-assembly
51
Fuel supply problem
Fuel leak, clog
  1. Fuel pump control system
  2. Fuel line
54 to 56
Ignition and injection stops (electrical system malfunction)
Power temporarily cut
  1. Power supply circuit (Fuel injector assembly, ignition coil assembly)
52, 53
  1. P1605:

A224367E03

1:
  1. If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.
  2. If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
2:
  1. If the air fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
  2. If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed
Suspected Area
Primary Parts to Inspect
Procedure
Slowly decreases
Air fuel ratio abnormal
Air suction
  1. Intake system connections
  2. Purge VSV system
  3. Brake booster assembly
3 to 6
Sensor malfunction (value from sensor too lean)
  1. Mass air flow meter sub-assembly
  2. Engine coolant temperature sensor
  3. Air fuel ratio sensor system
7 to 16
Sensor malfunction (value from sensor too rich)
25 to 34
Fuel supply problem
  1. Fuel pump control system
  2. Purge VSV system
  3. Fuel line
  4. ECM
17 to 24
Intake air volume insufficient
ISC flow rate
  1. Throttle with motor body assembly (ISC valve)
35 to 37
Ignition timing incorrect
Does not operate as expected
  1. Knock control sensor
  2. Engine coolant temperature sensor
  3. Mass air flow meter sub-assembly
40 to 42
Rapidly decreases
Ignition and injection stops (electrical system malfunction)
Power temporarily cut
  1. Power supply circuit (Fuel injector assembly, ignition coil assembly)
43, 44
External part malfunctioning
Increase in load
  1. Air conditioning system
  2. Power steering system
  3. A/T system
  4. Park/Neutral position switch assembly
47 to 49

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603 AND/OR P1605)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC P1603 and/or P1605 is output
    A
    DTC P1603 or P1605 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).



  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Problem Symptom
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Closed Throttle Position SW
    Engine Speed
    Total of Short FT and Long FT
    When idling or decelerating, engine speed slowly decreases (and engine stalls)
    All 5 sets of freeze frame data are ON
    Decreases slowly*1
    All 5 sets of freeze frame data are +15% or higher*2
    1. Air suction
    2. Sensor malfunction (value from sensor too lean)
    3. Fuel supply problem
    A
    At least 1 of the 5 sets of freeze frame data is -15% or less*3
    Sensor malfunction (value from sensor too rich)
    B
    All 5 sets of freeze frame data are between -15% and +15%
    1. Intake air volume insufficient
    2. Ignition timing incorrect
    C
    When idling or decelerating, engine speed rapidly decreases (and engine stalls)
    Decreases rapidly*1
    -
    1. Injection stoppage, ignition stoppage
    2. Load from external parts
    D
    When accelerating or driving at constant speed, engine stalls*4
    At least one is OFF
    -
    -
    1. Sensor malfunction
    2. Injection stoppage, ignition stoppage
    3. Fuel supply problem
    E


    A215381E06

    HINT:
    1. *1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.
      Otherwise, the engine speed is considered to have decreased slowly.
      1. In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or higher.
      2. In the freeze frame data, the engine speed at #5 is 120 rpm or less.
    1. If the vehicle speed is 20 km/h (12 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
    2. *2: When a DTC is stored, feedback compensation increases because the air fuel ratio is determined to be lean.
    3. *3: When a DTC is stored, feedback compensation decreases because the air fuel ratio is determined to be rich.
    4. *4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.



B
Go to step 25

C
Go to step 35

D
Go to step 43

E
Go to step 50
A


3.CHECK INTAKE SYSTEM
  1. Check for air leaks in the intake system (vacuum hose disconnection, cracks, damaged gaskets, etc.) (Click here).

    HINT:
    1. If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
    2. If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leaks may be present.

    OK:
    There is no air leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.CHECK PURGE VSV


    A255867E01
  1. Disconnect the fuel vapor feed hose assembly (on the canister side) of the purge VSV.

Text in Illustration 
*1
Fuel Vapor Feed Hose Assembly (to Canister)
*2
Purge VSV Connector
*3
Purge VSV
  1. Start the engine.

  1. Idle the engine.

  1. Disconnect the connector of the purge VSV.

  1. Check if air flows through the purge VSV.

    OK:
    Air does not flow.

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



NG
INSPECT PURGE VSV (Click here)
OK


5.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Stop Light Switch
    At least 1 of the 5 sets of freeze frame data is ON
    Air suction from brake booster assembly
    A
    All 5 sets of freeze frame data are OFF
    -
    B



B
Go to step 7
A


6.READ VALUE USING INTELLIGENT TESTER (SHORT FT #1 AND SHORT FT #2)
A217928E06
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Start the engine and warm it up until the engine coolant temperature stabilizes.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Idle the engine.

  1. Using the tester, read [Short FT #1 and Short FT #2] of the Data List while depressing the brake pedal.

    Standard:
    Short FT #1 or Short FT #2 changes by 10% or less.

    HINT:
    1. Even if the results are normal, the brake booster assembly may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the brake booster assembly (refer to step 57).
    1. When air leaks from the brake booster assembly is present, the feedback compensation increases because the air fuel ratio becomes lean.
    1. It is also possible to perform the airtightness inspection to check the brake booster assembly.



NG
REPLACE BRAKE BOOSTER ASSEMBLY (Click here)
OK


7.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Calculate Load
    Less than 90% of the current value of the vehicle*1
    Mass air flow meter sub-assembly
    A
    AFS Voltage B1S1 or AFS Voltage B2S1
    3.3 V or higher*2
    1. Air fuel ratio sensor
    2. Wire harness or connector
    3. Actual air fuel ratio abnormal
    B
    Both freeze frame data items listed above
    Values are other than above
    -
    C

    HINT:
    1. Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
    2. *1: If the mass air flow meter sub-assembly is malfunctioning, the freeze frame data will show a low engine load value.
    3. *2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is lean, the actual air fuel ratio will become rich and the engine may stall.



B
Go to step 9

C
Go to step 12
A


8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
  1. Remove the mass air flow meter sub-assembly (Click here).

  1. Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

    Result 
    Result
    Proceed to
    Visible foreign matter is present
    A
    Visible foreign matter is not present
    B

    HINT:
    1. Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).
    2. Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).



B
Go to step 12
A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)


    A215382E21
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and AFS Voltage B2S1.

  1. Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensors displayed on the tester.

    Standard:
    Tester Display
    Specified Condition
    Control the Injection Volume (12%)
    Air fuel ratio sensors output voltage is below 3.1 V
    Control the Injection Volume (-12%)
    Air fuel ratio sensors output voltage is higher than 3.4 V

    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B

    HINT:
    1. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    2. Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 57).



B
Go to step 12
A


10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
  1. Check the harnesses and connectors, referring to DTC P0031 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR POWER SOURCE CIRCUIT (AIR FUEL RATIO SENSOR POWER SOURCE)
OK


11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P2237 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR FUEL RATIO SENSOR (Click here)  

12.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Proceed to
    Initial Engine Coolant Temp, Initial Intake Air Temp
    Difference in temperature between each item is below 10°C (18°F)*1
    A
    Difference in temperature between each item is 10°C (18°F) or higher*2
    B

    HINT:
    1. *1: A long time had elapsed after stopping the engine.
    2. *2: A long time had not elapsed after stopping the engine.



B
Go to step 15
A


13.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).



  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).


    A217929E21


    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Initial Engine Coolant Temp, Coolant Temp, Engine Run Time
    Range A
    1. Engine coolant temperature sensor
    2. Thermostat
    A
    Range B
    Engine coolant temperature sensor
    B
    Range C
    -
    C

    HINT:
    This step is not directly related to engine stall.



B
Go to step 16

C
Go to step 17
A


14.INSPECT THERMOSTAT
  1. Inspect the thermostat (Click here).


Result 
Result
Proceed to
Abnormal
A
Normal
B

HINT:
This step is not directly related to engine stall.



B
Go to step 16
A

REPLACE THERMOSTAT (Click here)  

15.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Coolant Temp
    120°C (248°F) or higher
    Engine coolant temperature sensor
    A
    Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher
    Engine coolant temperature sensor
    Both freeze frame data items listed above
    Values are other than above
    -
    B

    HINT:
    *: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.



B
Go to step 17
A


16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    1. Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 57).
    2. Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


17.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    EVAP (Purge) VSV
    At least 1 of the 5 sets of freeze frame data is not 0%
    Purge VSV
    A
    All 5 sets of freeze frame data are 0%
    -
    B

    HINT:
    If the purge VSV is stuck closed, air fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air fuel ratio becomes lean and the engine may stall.



B
Go to step 22
A


18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)


    A255866E01
  1. Disconnect the fuel vapor feed hose assembly (on the canister side) of the purge VSV.
    Text in Illustration 
    *1
    Purge VSV
    *2
    Fuel Vapor Feed Hose Assembly (to Canister)

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.

  1. Operate the purge VSV and check the air flow.

    OK:
    Activate the VSV for Evap Control
    Specified Condition
    ON
    Air flows
    OFF
    Air does not flow

    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Even if the results are normal, the purge VSV may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the purge VSV (refer to step 57).



B
Go to step 22
A


19.INSPECT PURGE VSV
  1. Inspect the purge VSV (Click here).



NG
REPLACE PURGE VSV (Click here)
OK


20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
  1. Check the harnesses and connectors, referring to DTC P0443 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR POWER SOURCE CIRCUIT (PURGE VSV POWER SOURCE)
OK


21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
  1. Check the harnesses and connectors, referring to DTC P0443 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for an operating sound from the fuel pump.

    OK:

    Control the Fuel Pump / Speed
    Specified Condition
    ON
    Operating sound heard
    OFF
    Operating sound not heard


    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
    3. If the fuel pump operating noise is abnormal, proceed to step 23.



B
Go to step 24
A


23.INSPECT FUEL PUMP (RESISTANCE)
  1. Inspect the fuel pump (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK

CHECK FUEL PUMP CONTROL CIRCUIT (Click here)  

24.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.

    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B

    HINT:
    If there is foreign matter such as iron particles on the fuel pump, remove the foreign matter.



B
Go to step 57
A

REPAIR OR REPLACE FUEL SYSTEM 

25.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Calculate Load
    110% or higher of the current value of the vehicle*1
    Mass air flow meter sub-assembly
    A
    AFS Voltage B1S1 or AFS Voltage B2S1
    Less than 3.3 V*2
    1. Air fuel ratio sensor
    2. Harness and connector
    3. Actual air fuel ratio abnormal
    B
    Both freeze frame data items listed above
    Values are other than above
    -
    C

    HINT:
    1. Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
    2. *1: If the mass air flow meter sub-assembly is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake air surge tank assembly, the freeze frame data will show a high engine load value.
    3. *2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is rich, the actual air fuel ratio will become lean and the engine may stall.



B
Go to step 27

C
Go to step 30
A


26.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
  1. Remove the mass air flow meter sub-assembly (Click here).

  1. Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

    Result 
    Result
    Proceed to
    Visible foreign matter is present
    A
    Visible foreign matter is not present
    B

    HINT:
    1. Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).
    2. Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).



B
Go to step 30
A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)


    A215382E21
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and AFS Voltage B2S1.

  1. Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensors displayed on the tester.

    Standard:
    Tester Display
    Specified Condition
    Control the Injection Volume (12%)
    Air fuel ratio sensors output voltage is below 3.1 V
    Control the Injection Volume (-12%)
    Air fuel ratio sensors output voltage is higher than 3.4 V

    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B

    HINT:
    1. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    2. Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 57).



B
Go to step 30
A


28.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
  1. Check the harnesses and connectors, referring to DTC P0031 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR POWER SOURCE CIRCUIT (AIR FUEL RATIO SENSOR POWER SOURCE)
OK


29.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P2237 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR FUEL RATIO SENSOR (Click here)  

30.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Proceed to
    Initial Engine Coolant Temp, Initial Intake Air Temp
    Difference in temperature between each item is below 10°C (18°F)*1
    A
    Difference in temperature between each item is 10°C (18°F) or higher*2
    B

    HINT:
    1. *1: A long time had elapsed after stopping the engine.
    2. *2: A long time had not elapsed after stopping the engine.



B
Go to step 33
A


31.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).



  1. Using the tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data (Click here).


    A217929E21


    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Initial Engine Coolant Temp, Coolant Temp, Engine Run Time
    Range A
    1. Engine coolant temperature sensor
    2. Thermostat
    A
    Range B
    Engine coolant temperature sensor
    B
    Range C
    -
    C

    HINT:
    This step is not directly related to engine stall.



B
Go to step 34

C
Go to step 58
A


32.INSPECT THERMOSTAT
  1. Inspect the thermostat (Click here).


Result 
Result
Proceed to
Abnormal
A
Normal
B

HINT:
This step is not directly related to engine stall.



B
Go to step 34
A

REPLACE THERMOSTAT (Click here)  

33.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Coolant Temp
    120°C (248°F) or higher
    Engine coolant temperature sensor
    A
    Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher
    Engine coolant temperature sensor
    Both freeze frame data items listed above
    Values are other than above
    -
    B

    HINT:
    *: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.



B
Go to step 58
A


34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).


Result 
Result
Proceed to
Abnormal
A
Normal
B

HINT:
  1. Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. If there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 57).
  2. Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



B
Go to step 57
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

35.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Total of ISC Learning Value and ISC Feedback Value
    Less than 80% of the current value of the vehicle*1
    Throttle with motor body assembly
    A
    120% or higher of the current value of the vehicle*2
    B
    From 80 to 120% of the current value of the vehicle
    -
    C

    HINT:
    1. Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
    2. *1: If the throttle with motor body assembly has a temporary problem in which it cannot fully close, the intake air volume and engine speed increase. As a result, the ISC learning amount becomes less than the standard. At this time, if the throttle with motor body assembly returns to normal and fully closes, the intake air volume will be insufficient and the engine may stall.
    3. *2: If carbon accumulates on the throttle with motor body assembly and the intake air volume decreases, the ISC learning amount is increased to maintain the idle speed. If this situation continues, the ISC learning amount reaches the upper limit, the idle speed cannot be maintained causing idling to become unstable, and the engine may stall.



B
Go to step 37

C
Go to step 38
A


36.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check for foreign matter and signs that the throttle with motor body assembly was stuck, and also check that the valve and shaft move smoothly during operation.

    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B

    HINT:
    1. Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 42, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 57).
    2. Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



B
Go to step 38
A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)  

37.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the air flow passage of the throttle with motor body assembly.

    Result 
    Result
    Proceed to
    Carbon in passage
    A
    No carbon in passage
    B

    HINT:
    1. Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 42, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 57).
    2. Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



B
Go to step 38
A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)  

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
  1. Perform the Active Test, referring to DTC P0011 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
    3. If the camshaft timing oil control valve assembly (for intake camshaft) is stuck at the advanced side, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) (Click here)
OK


39.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)
  1. Perform the Active Test, referring to DTC P0014 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
    3. If the camshaft timing oil control valve assembly (for exhaust camshaft) is stuck at the retard side, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) (Click here)
OK


40.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    IGN Advance
    Knock Correct Learn Value
    Differs from the current value of the vehicle by 10 deg or more
    Below 3°CA
    1. Engine coolant temperature sensor
    2. Mass air flow meter sub-assembly
    3. Knock control sensor
    A
    3°CA or more
    -
    B
    Differs from the current value of the vehicle by less than 10 deg
    -
    -

    HINT:
    1. Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
    2. Even if the results are normal, the knock control sensors may have been malfunctioning. If there are no problems with other parts, replace the knock control sensors (refer to step 57).



B
Go to step 57
A


41.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


42.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
  1. Inspect the mass air flow meter sub-assembly (intake air temperature sensor) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly or knock control sensor (Click here).



NG
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)
OK

REPLACE KNOCK CONTROL SENSOR (Click here)  

43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
  1. Check the harnesses and connectors, referring to DTC P0300 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)



NG
REPAIR POWER SOURCE CIRCUIT (FUEL INJECTOR ASSEMBLY POWER SOURCE)
OK


44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
  1. Check the harnesses and connectors, referring to DTC P0351 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)



NG
REPAIR POWER SOURCE CIRCUIT (IGNITION COIL ASSEMBLY POWER SOURCE)
OK


45.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Idle Spark Advn Ctrl (#1 to #6)
    At least one cylinder shows a value of 4°CA or higher
    1. Fuel injector system
    2. Ignition coil system
    A
    All cylinders show a value of less than 4°CA
    -
    B



B
Go to step 47
A


46.READ VALUE USING INTELLIGENT TESTER (IDLE SPARK ADVN CTRL #)
  1. Change the location of the ignition coil assembly for the cylinder whose Idle Spark Advn Ctrl (#1 to #6) was 4°CA or more in step 45.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Using the tester, select [Idle Spark Advn Ctrl (#1 to #6)] of the Data List.

    Result 
    Result
    Proceed to
    Same as result in step 45
    A
    Different from result in step 45
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Perform "Inspection After Repair" after replacing the ignition coil assembly (Click here).



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A


47.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    A/C Signal
    Air Conditioner FB Val
    Power Steering Signal
    A/C Signal display changes from OFF to ON
    Value displayed for Air Conditioner FB Val increases
    Does not change from OFF
    A/C system
    B
    Changes from OFF to ON
    Power steering system
    A
    A/C Signal display does not change from OFF
    Value displayed for Air Conditioner FB Val does not increase
    Changes from OFF to ON
    Does not change from OFF
    -

    HINT:
    1. Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
    2. The normal value for the ISC learning amount is engine displacement (liters) x 0.9.
    3. Even if the results are normal, the power steering system or the air conditioning system may have been malfunctioning. Continue this inspection procedure until step 49, and if there are no problems with other parts, inspect the power steering system and the air conditioning system (refer to step 57).



B
CHECK AIR CONDITIONING SYSTEM (Click here)
A


48.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Electrical Load Signal 1
    Electric Load Feedback Val
    Difference between Engine Speed and SPD (NT)
    Vehicle Speed
    Electrical Load Signal 1 display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1
    Value displayed for Electric Load Feedback Val changes
    -
    -
    Electrical load signal circuit
    A
    Value displayed for Electric Load Feedback Val does not change
    At least 1 of the 5 sets of freeze frame data is less than 100 rpm
    Less than 20 km/h (12 mph)
    A/T system
    B
    20 km/h (12 mph) or higher
    -
    C
    All 5 sets of freeze frame data are 100 rpm or higher
    -
    -
    C
    Electrical Load Signal 1 display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase
    -
    At least 1 of the 5 sets of freeze frame data is less than 100 rpm
    Less than 20 km/h (12 mph)
    A/T system
    B
    20 km/h (12 mph) or higher
    -
    C
    All 5 sets of freeze frame data are 100 rpm or higher
    -
    -
    C

    HINT:
    1. *1: If the Electrical Load Signal 1 display changes from OFF to ON or the Electric Load Feedback Val increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
    2. If the vehicle speed is 20 km/h (12 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
    3. The normal value for the ISC learning amount is engine displacement (liters) x 0.9.
    4. Even if the results are normal, the electrical load signal system and/or the A/T system may have been malfunctioning. Continue this inspection procedure until step 49, and if there are no problems with other parts, inspect the electrical load system and/or the A/T system (refer to step 57).



B
CHECK AUTOMATIC TRANSAXLE SYSTEM (Click here)

C
Go to step 49
A

CHECK GENERATOR CIRCUIT (Click here)  

49.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Shift SW Status (P or N Range)
    Neutral Position SW Signal
    P and N position are both OFF in at least one data set
    ON when Shift SW Status D or R
    Park/Neutral position switch assembly
    A
    OFF when Shift SW Status D or R
    A/T system
    B
    All 5 sets of freeze frame data are ON
    -
    -
    C

    HINT:
    Even if the results are normal, the park/neutral position switch assembly and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or A/T system (refer to step 57).



B
CHECK AUTOMATIC TRANSAXLE SYSTEM (Click here)

C
Go to step 57
A

CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)  

50.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Throttle Sensor Position, Calculate Load
    Calculate Load decreases while Throttle Sensor Position increases
    Mass air flow meter sub-assembly
    A
    Calculate Load does not decrease while Throttle Sensor Position increases
    -
    B



B
Go to step 52
A


51.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
  1. Remove the mass air flow meter sub-assembly (Click here).

  1. Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

    Result 
    Result
    Proceed to
    Visible foreign matter is present
    A
    Visible foreign matter is not present
    B

    HINT:
    1. Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 56, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).
    2. Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).



B
Go to step 52
A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

52.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
  1. Check the harnesses and connectors, referring to DTC P0300 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)



NG
REPAIR POWER SOURCE CIRCUIT (FUEL INJECTOR ASSEMBLY POWER SOURCE)
OK


53.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
  1. Check the harnesses and connectors, referring to DTC P0351 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)



NG
REPAIR POWER SOURCE CIRCUIT (IGNITION COIL ASSEMBLY POWER SOURCE)
OK


54.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for an operating sound from the fuel pump.

    OK:

    Control the Fuel Pump / Speed
    Specified Condition
    ON
    Operating sound heard
    OFF
    Operating sound not heard


    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
    3. If the fuel pump operating noise is abnormal, proceed to step 56.



B
Go to step 56
A


55.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK

CHECK FUEL PUMP CONTROL CIRCUIT (Click here)  

56.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.

    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B

    HINT:
    If there is foreign matter such as iron particles on the fuel pump, remove the foreign matter.



B
Go to step 57
A

REPAIR OR REPLACE FUEL SYSTEM 

57.REPLACE MALFUNCTIONING PARTS
  1. If the malfunction could not be identified in steps 3 to 24, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

    Performed Step
    Inspection or Part to Replace
    Step 6
    Brake booster assembly replacement
    Step 8
    Mass air flow meter sub-assembly replacement
    Step 9
    Air fuel ratio sensor replacement
    Step 16
    Engine coolant temperature sensor replacement
    Step 18
    Purge VSV replacement
    Step 24
    Fuel pump replacement

  1. If the malfunction could not be identified in steps 25 to 34, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

    Performed Step
    Inspection or Part to Replace
    Step 26
    Mass air flow meter sub-assembly replacement
    Step 27
    Air fuel ratio sensor replacement
    Step 34
    Engine coolant temperature sensor replacement

  1. If the malfunction could not be identified in steps 35 to 42, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

    Performed Step
    Inspection or Part to Replace
    Step 36, 37
    Throttle with motor body assembly replacement
    Step 40
    Knock control sensor replacement

  1. If the malfunction could not be identified in steps 43 to 49, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.

    Performed Step
    Inspection or Part to Replace
    Step 47
    A/C system inspection and repair
    Power steering system inspection and repair
    Step 48
    Electrical load system inspection and repair
    A/T system inspection and repair
    Step 49
    Park/Neutral position switch assembly inspection and repair
    A/T system inspection and repair

  1. If the malfunction could not be identified in steps 50 to 56, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

    Performed Step
    Inspection or Part to Replace
    Step 51
    Mass air flow meter sub-assembly replacement

    HINT:
    1. Referring to the chart, inspect and repair or replace the part from the step where an inspection was performed.
    2. Perform "Inspection After Repair" after replacing or servicing parts related to engine operation. Refer to detailed information in Initialization (Click here).


NEXT


58.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Clear the DTCs (Click here).


NEXT


59.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check if engine stall symptoms are present.

    HINT:
    If any engine stall symptoms are present, recheck for DTCs and freeze frame data and perform an inspection.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS
OK

END