DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
DTC P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0016 | Deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 1) signal (2 trip detection logic). |
|
| P0018 | Deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 2) signal (2 trip detection logic). |
| Required Sensors/Components (Main) | Camshaft timing gear assembly |
| Required Sensors/Components (Related) | VVT sensor Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Engine speed | 500 to 1000 rpm |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0016 or P0018 is output | A |
| DTC P0016 or P0018 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the A/C switch on.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) / All Data / VVT Change Angle #1 or VVT Change Angle #2.
Perform the Active Test. Check that the displacement angle varies.
|
| ||||
| OK | |
| 3.ADJUST VALVE TIMING |
Adjust the valve timing (Click here).
|
| ||||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for intake camshaft) (Click here).
|
| ||||
| OK | |
| 5.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE |
![]() |
Remove the oil pipe or No. 1 oil pipe (Click here).
Remove the oil control valve filter RH or oil control valve filter LH.
Check that the oil control valve filter and oil pipe are not clogged.
| *1 | Bank 1 |
| *2 | Bank 2 |
| *a | Oil Pipe |
| *b | No. 1 Oil Pipe |
|
| ||||
| OK | |
| 6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Inspect the camshaft timing gear assembly .
|
| ||||
| OK | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0016 or P0018 is output | B |
|
| ||||
| A | ||
| ||