Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0037    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

DTC    P0038    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)

DTC    P0141    Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)

DTC    P102D    O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON

for Preparation Click here


DESCRIPTION

Refer to DTC P0136 .

HINT:
  1. Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.

  2. When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.


    A255121E02


DTC No.
DTC Detection Condition
Trouble Area
P0037
Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
  1. Open in heated oxygen sensor (sensor 2) heater circuit
  2. Heated oxygen sensor (sensor 2)
  3. No. 1 integration relay
  4. ECM
P0038
Heated oxygen sensor heater current reaches high limit
(Hybrid IC high current limiter monitor input "Fail") (1 trip detection logic).
  1. Short in heated oxygen sensor (sensor 2) heater circuit
  2. Heated oxygen sensor (sensor 2)
  3. No. 1 integration relay
  4. ECM
P0141
The cumulative heater resistance correction value exceeds the threshold (2 trip detection logic).
  1. Open or short in heated oxygen sensor (sensor 2) heater circuit
  2. Heated oxygen sensor (sensor 2)
  3. No. 1 integration relay
  4. ECM
P102D
Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
ECM

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
  1. Heated Oxygen Sensor Heater Range Check (P0037, P0038 and P102D):
    1. The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.
      If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
  1. Heated Oxygen Sensor Heater Performance (P0141):
    1. After the accumulated heater on time exceeds 100 seconds, the ECM calculates the heater resistance using battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM determines that there is a malfunction in the heated oxygen sensor heater and stores DTC P0141.

MONITOR STRATEGY


Related DTCs
P0037: Heated oxygen sensor heater (sensor 2) range check (low current)
P0038: Heated oxygen sensor heater (sensor 2) range check (high current)
P0141: Heated oxygen sensor heater performance (sensor 2)
P102D: Heated oxygen sensor heater performance (sensor 2)
Required Sensors/Components (Main)
Heated oxygen sensor heater (sensor 2)
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous: P0037, P0038, P102D
Once per driving cycle: P0141
Duration
0.5 seconds: P0037
Within 3 seconds: P0038
10 seconds: P0141
0.5 seconds: P102D
MIL Operation
Immediate: P0037, P0038, P102D
2 driving cycles: P0141
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None

P0037: (Case 1) 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Engine
Running
Starter
Off
Catalyst active A/F control
Not operating
Time after heater on
10 seconds or more
Learned heater off current operation
Completed
Learned heater off current operation
Succeeded
Oxygen sensor heater high current fail (P0038)
Not detected
Heater on current - Learned heater off current
0.15 A or less
Heater output
On

P0037: (Case 2) 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Engine
Running
Starter
Off
Catalyst active A/F control
Not operating
Time after heater on
10 seconds or more
Learned heater off current operation
Completed
Oxygen sensor heater high current fail (P0038)
Not detected
Heater off current
Higher than 3.5 A
Hybrid IC high current limiter monitor input
Fail

P0038 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Engine
Running
Starter
Off
Catalyst active A/F control
Not operating
Time after heater on
10 seconds or more
Learned heater off current operation
Completed
Hybrid IC high current limiter monitor input
Fail
Heater output
On

P0141 
All of the following conditions are met
-
Heated oxygen sensor heater circuit fail (P0037, P0038 and P102D)
Not detected
Battery voltage
10.5 V or higher
Fuel cut
Off
Time after fuel cut on to off
30 seconds or more
Accumulated heater on time
100 seconds or more
Learned heater off current operation
Completed
Duration that heated oxygen sensor impedance is less than 15 kΩ
2 seconds or more

P102D 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Engine
Running
Starter
Off
Catalyst active A/F control
Not operating
Time after heater on
10 seconds or more
Learned heater off current operation
Completed
Oxygen sensor heater low current fail (P0037)
Not detected
Oxygen sensor heater high current fail (P0038)
Not detected
Heater output
Off
Heater off current
Higher than 3.5 A
Hybrid IC high current limiter monitor input
Fail

TYPICAL MALFUNCTION THRESHOLDS


P0037: (Case 1) 
Heater on current - Learned heater off current
0.15 A or less

P0037: (Case 2) 
Heater on current
1 A or less

P0038 
Both of the following conditions are met
-
Hybrid IC high current limiter monitor input
Fail
Heater output
On

P0141 
Heater resistance
Varies with sensor element temperature (Example: Higher than 23 Ω)

P102D 
Heater on current
Higher than 1 A

MONITOR RESULT

Refer to detailed information in Checking Monitor Status (Click here).

P0141: O2 Sensor Heater / O2 HEATER B1S2 
Monitor ID
Test ID
Scaling
Unit
Description
$42
$91
Multiply by 0.001
Ohm
Oxygen sensor heater resistance bank 1 sensor 2

CONFIRMATION DRIVING PATTERN


A262623E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0037, P0038, P0141 or P102D.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A266345E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2] (Click here).
  4. When the values for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.
  5. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  6. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)


    A213333E11
  1. Disconnect the heated oxygen sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E21-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E21-1 (HT1B) - E26-24 (HT1B)
    Always
    Below 1 Ω
    E21-1 (HT1B) or E26-24 (HT1B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0141 OR P102D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the pending DTCs.


Result 
Result
Proceed to
DTC is not output
A
DTC P0037, P0038, P0141 or P102D is output
B


B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E21-2 (+B) - 1A-6
    Always
    Below 1 Ω
    E21-2 (+B) or 1A-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)


    A256530E02
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1D-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)