DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 | Either of the following conditions is met:
|
|
| P0137 | Either of the following conditions is met:
|
|
| P0138 |
|
|
| P0139 | Either of the following conditions is met:
|
|
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0136 | Not applicable | None |
| P0137 |
|
|
| P0138 | Not applicable | None |
| P0139 | Not applicable | None |
| Active Air fuel Ratio Control |
| Abnormal Voltage Output of Heated Oxygen (HO2) Sensor (DTC P0136) |

| Open in Heated Oxygen (HO2) Sensor Circuit (DTC P0137) |

| High or Low Impedance of Heated Oxygen (HO2) Sensor (DTCs P0136 or P0137) |
![]() |
| Extremely High Output Voltage of Heated Oxygen (HO2) Sensor (DTC P0138) |
| Abnormal Voltage Output of Heated Oxygen (HO2) Sensor During Fuel-cut (DTC P0139) |
| Related DTCs | P0136: Heated oxygen sensor (bank 1) voltage check (voltage malfunction) P0136: Heated oxygen sensor (bank 1) circuit continuity check (circuit short) P0137: Heated oxygen sensor (bank 1) voltage check (low voltage) P0136: Heated oxygen sensor (bank 1) circuit continuity check (circuit open) P0138: Heated oxygen sensor (bank 1) circuit continuity check (out of range) P0139: Heated oxygen sensor (bank 1) response rate during fuel cut |
| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Mass air flow meter sub-assembly Throttle position sensor Air fuel ratio sensor |
| Frequency of Operation | Once per driving cycle: Active air fuel ratio control detection, heated oxygen sensor abnormal voltage during fuel cut. Continuous: Other |
| Duration | 20 seconds: Heated oxygen sensor voltage check 30 seconds: Heated oxygen sensor circuit continuity check (circuit short) 90 seconds: Heated oxygen sensor circuit continuity check (circuit open) 10 seconds: Heated oxygen sensor circuit continuity check (out of range) 7 seconds: Heated oxygen sensor response rate during fuel cut |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0016 (VVT system - misalignment) P0017 (Exhaust VVT system - misalignment) P0031, P0032, P101D (Air fuel ratio sensor heater) P0037, P0038, P102D (Heated oxygen sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P01235 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172 (Fuel system) P0301 - P0304 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0451, P0452, P0453 (EVAP system) P0500 (Vehicle speed sensor) P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253, P2A00 (Air fuel ratio sensor) P219A (Air fuel ratio imbalance) |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idling | Off |
| Engine speed | Less than 3000 rpm (except PZEV) Less than 4000 rpm (for PZEV) |
| A/F sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10 to 90% (except PZEV) 10 to 80% (for PZEV) |
| Shift position | 4th or higher (except PZEV) 5th or higher (for PZEV) |
| Battery voltage | 11 V or higher |
| Estimated heated oxygen sensor temperature | Less than 700°C (1292°F) |
| ECM monitor | Completed |
| DTC P0607 | Not set |
| Battery voltage | 11 V or higher |
| Estimated heated oxygen sensor temperature | 450°C (842°F) or higher, and less than 750°C (1382°F) |
| DTC P0607 | Not set |
| Battery voltage | 11 V or higher |
| Time after engine start | 2 seconds or more |
| Engine coolant temperature | 75°C (167°F) or higher |
| Catalyst temperature | 400°C (752°F) or higher |
| Fuel cut | On |
| All of the following conditions (a), (b) and (c) met | - |
| (a) OSC (Oxygen Storage Capacity of Catalyst) | 2.7 g or more (except PZEV) 2.3 g or more (for PZEV) |
| (b) Commanded air fuel ratio | 14.4 or less |
| (c) Rear HO2 sensor voltage | 0.21 V or higher, and less than 0.69 V |
| All of the following conditions (a), (b) and (c) met | - |
| (a) OSC (Oxygen Storage Capacity of Catalyst) | 2.7 g or more (except PZEV) 2.3 g or more (for PZEV) |
| (b) Commanded air fuel ratio | 14.4 or less |
| (c) Rear HO2 sensor voltage | Less than 0.21 V |
| Duration of following condition | 30 seconds or more |
| Heated oxygen sensor impedance | Less than 5 Ω |
| Duration of following condition | 90 seconds or more |
| Heated oxygen sensor impedance | 15 kΩ or higher |
| Duration of following condition | 10 seconds or more |
| Heated oxygen sensor voltage | 1.2 V or higher |
| Either of the following conditions is met | - |
| Duration until heated oxygen sensor voltage drops to 0.2 V after fuel cut | 7 seconds or more |
| Duration until heated oxygen sensor voltage drops from 0.35 V to 0.2 V during fuel cut | 1 second or more |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $08 | Multiply by 0.001 | V | Maximum sensor voltage |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $8B | Multiply by 0.001 | Seconds | 0.35 - 0.2 V sensor switch time |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $8D | Multiply by 0.001 | Seconds | Duration that sensor voltage drops to 0.2 V during fuel-cut |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $02 | $8F | Multiply by 0.0003 | g | Maximum oxygen storage capacity |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | +12% | Rich | Below 3.1 V |
| -12% | Lean | Higher than 3.4 V | |
| O2S B1S2 (Heated oxygen) | +12% | Rich | Higher than 0.55 V |
| -12% | Lean | Below 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.READ OUTPUT DTC (DTC P0136, P0137, P0138 OR P0139) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0138 is output | A |
| P0137 is output | B |
| P0136 is output | C |
| P0139 is output | D |
| P0136, P0137 or P0138 and other DTCs are output | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| *a | Component without harness connected (Heated Oxygen Sensor) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the ignition switch to off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-24 (HT1B) - E26-100 (OX1B) | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Gas AF Control / O2S B1S2.
Change the fuel injection volume using the Techstream, and monitor the voltage output of heated oxygen sensor displayed on the Techstream.
|
| ||||
| OK | |
| 5.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.
Change the fuel injection volume using the Techstream, and monitor the voltage output of air fuel ratio and heated oxygen sensors displayed on the Techstream.
| Techstream Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 (Air fuel ratio) | Alternates between higher and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 7.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E21-1 (HT1B) - E26-24 (HT1B) | Always | Below 1 Ω |
| E21-3 (OX1B) - E26-100 (OX1B) | Always | Below 1 Ω |
| E21-4 (E2) - E26-132 (EX1B) | Always | Below 1 Ω |
| E21-1 (HT1B) or E26-24 (HT1B) - Body ground | Always | 10 kΩ or higher |
| E21-3 (OX1B) or E26-100 (OX1B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 10.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0136, P0137 and P0138).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137 or P0138.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0136, P0137 or P0138 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | ||
| ||
| 12.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0136, P0137 and P0138).
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0136 is output) | B |
|
| ||||
| A | ||
| ||
| 15.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 16.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
Turn the ignition switch off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-24 (HT1B) - E26-100 (OX1B) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 17.PERFORM CONFIRMATION DRIVING PATTERN |
Perform the Confirmation Driving Pattern (P0139).
| NEXT | |
| 18.READ OUTPUT DTC (DTC P0139 IS OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0139.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0139 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | ||
| ||