VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON |

| 1.CHECK CAN COMMUNICATION SYSTEM |
Check if a CAN communication system DTC is output (Click here).
| Result | Proceed to |
| DTC is not output. | A |
| DTC is output. | B |
|
| ||||
| A | |
| 2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU connector is securely connected.
|
| ||||
| OK | |
| 3.CHECK BATTERY |
Check the battery voltage.
| Result | Proceed to |
| OK | A |
| NG (for 2GR-FE) | B |
| NG (for 2AR-FE) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL) |
![]() |
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-25 (+BS) - Body ground | Always | 11 to 14 V |
| A49-25 (+BS) - A49-38 (GND1) | Always | 11 to 14 V |
| A49-28 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| A49-28 (IG1) - A49-38 (GND1) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
![]() |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-38 (GND1) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | |
| 6.READ VALUE USING TECHSTREAM (PARKING BRAKE SWITCH ASSEMBLY) |
Reconnect the skid control ECU connector.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the Techstream (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied OFF: Parking brake released | - |
Using the Techstream, check the switch operation signal received when the parking brake is operated.
|
| ||||
| OK | |
| 7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
![]() |
Turn the ignition switch off.
Remove the reservoir filler cap and the strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (+) - 2 (E) | Switch OFF (Float up) | 1.9 to 2.1 kΩ |
| 1 (+) - 2 (E) | Switch ON (Float down) | Below 1 Ω |
| *a | Component without harness connected (Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly)) |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-19 (SW) - A30-1 (+) | Always | Below 1 Ω |
| I18-19 (SW) - Body ground | Always | 10 kΩ or higher |
| A30-2 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.INSPECT COMBINATION METER ASSEMBLY |
Reconnect the combination meter assembly connector and the brake fluid level warning switch connector.
Perform an Active Test of the combination meter assembly (meter CPU) using the Techstream (Click here).
Check the combination meter assembly.
|
| ||||
| OK | ||
| ||
| 10.INSPECT PARKING BRAKE SWITCH ASSEMBLY |
![]() |
Turn the ignition switch off.
Disconnect the parking brake switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (+) - Body ground | Parking brake switch ON (Switch pin free) | Below 1 Ω |
| 1 (+) - Body ground | Parking brake switch OFF (Switch pin pushed in) | 10 kΩ or higher |
| *a | Component without harness connected (Parking Brake Switch Assembly) |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH ASSEMBLY) |
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3D-20 (PKB) - A42-1 (+) | Always | Below 1 Ω |
| 3D-20 (PKB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||