Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Engine Coolant Temperature Receiver Gauge Malfunction

for Preparation Click here


DESCRIPTION

In this circuit, the meter ECU receives engine coolant temperature signals from the ECM using the CAN communication system. The meter ECU displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM


E143765E66


INSPECTION PROCEDURE

HINT:
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI System (Click here for 2AR-FE, Click here for 2GR-FE).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).

    Result:

    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (WATER TEMPERATURE METER OPERATION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Water Temperature Meter Operation
    Engine coolant temperature receiver gauge
    Low, Normal, High
    -

    OK:
    Engine coolant temperature receiver gauge indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.CHECK SFI SYSTEM
  1. Check if the SFI system output the DTC (Click here for 2AR-FE, Click here for 2GR-FE).


Result:

Result
Proceed to
The DTC is not output.
A
The DTC is output (for 2AR-FE).
B
The DTC is output (for 2GR-FE).
C



B
GO TO SFI SYSTEM (for 2AR-FE) (Click here)

C
GO TO SFI SYSTEM (for 2GR-FE) (Click here)
A


4.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE, COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus:

    1. for Combination Meter: Body Electrical / Combination Meter / Data List.

    2. for Engine and ECT: Powertrain / Engine and ECT / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/-40 to 140°C (-40 to 284°F)
    After warming up: 75 to 100°C (167 to 212°F)
    1. If -40°C (-40°F): Sensor circuit open
    2. If 140°C (284°F) or more: Sensor circuit shorted

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temp
    Coolant temperature/Min.: -40°C (-40°F), Max.: 140°C (284°F)
    75 to 100°C (167 to 212°F): After warming up
    1. Stored as Freeze Frame Data
    2. This is the engine coolant temperature.

    HINT:
    1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
    2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    3. If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.
    4. Check if the engine overheats when the value indicates higher than 135°C (275°F).


    Result:

    Result
    Proceed to
    The Data List values of the ECUs match.
    A
    The Data List values of the ECUs do not match (for 2AR-FE).
    B
    The Data List values of the ECUs do not match (for 2GR-FE).
    C

    HINT:
    1. When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
    2. When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected



B
REPLACE ECM (for 2AR-FE) (Click here)

C
REPLACE ECM (for 2GR-FE) (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)