DTC P050A Cold Start Idle Air Control System Performance |

| DTC No. | DTC Detection Condition | Trouble Area |
| P050A | Insufficient mass air flow after a cold start (2 trip detection logic). |
|
| Related DTCs | P050A: Cold start idle air speed control system |
| Required Sensors/Components (Main) | Throttle with motor body assembly |
| Required Sensors/Components (Related) | Mass air flow meter sub-assembly Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0010 (VVT oil control valve) P0011 (VVT system - advance) P0012 (VVT system - retard) P0016 (VVT system - misalignment) P0013 (Exhaust VVT oil control valve) P0014 (Exhaust VVT system - advance) P0015 (Exhaust VVT system - retard) P0017 (Exhaust VVT system - misalignment) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0171, P0172 (Fuel system) P0301 - P0304 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0365, P0367, P0368 (Exhaust camshaft position sensor) P0351 - P0354 (Igniter) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253, P2A00 (Air fuel ratio sensor) P219A (Air fuel ratio imbalance) |
| Battery voltage | 8 V or higher |
| Time after engine start | 3 seconds or more |
| Starter | Off |
| Engine coolant temperature at engine start | -10°C (14°F) or higher |
| Engine coolant temperature | -10°C (14°F) or higher, and less than 50°C (122°F) |
| Engine idling time | 3 seconds or more |
| Fuel-cut | Off |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Time after shift position changed | 1 second or more |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Accumulated mass air flow | Less than 28.75 g (varies with engine coolant temperature and engine coolant temperature at engine start) (except PZEV) Less than 66.875 g (varies with engine coolant temperature and engine coolant temperature at engine start) (for PZEV) |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P050A is output | A |
| DTC P050A and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (FUEL TRIM) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Gas AF Control / Short FT #1 and Long FT #1.
Read the values displayed on the Techstream at engine idle.
Add together the Short FT #1 and Long FT #1 values to obtain the total fuel trim.
|
| ||||
| OK | |
| 3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE) |
Check that there are no deposits around the throttle valve and throttle valve condition.
|
| ||||
|
| ||||
| 4.REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Repair or replace the throttle with motor body assembly (Click here).
|
| ||||
| 5.CHECK PCV SYSTEM |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 6.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks .
|
| ||||
| OK | |
| 7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY) |
Operate the VVT system through the Active test, and check if the VVT system is operating normally.
Perform the Active Test, referring to DTC P0011 Inspection Procedure (VVT system for intake camshaft) .
Perform the Active Test, referring to DTC P0014 Inspection Procedure (VVT system for exhaust camshaft) .
|
| ||||
| OK | |
| 9.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
| Techstream Display | Condition | Specified Condition |
| MAF | Shift lever position: N A/C: Off Engine Speed: 3000 rpm | Between 8 gm/sec and 22 gm/sec |
|
| ||||
|
| ||||
| 10.REPAIR OR REPLACE PCV HOSE |
Repair or replace the PCV valve or hose.
|
| ||||
| 11.REPAIR OR REPLACE INTAKE SYSTEM |
Repair or replace the intake system.
|
| ||||
| 12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Replace the air cleaner filter element sub-assembly.
|
| ||||
| 13.CHECK AND REPAIR VVT SYSTEM |
Check and repair the VVT system.
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).
Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050A.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050A is output) | B |
|
| ||||
| A | ||
| ||
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).
Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050A.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050A is output) | B |
|
| ||||
| A | ||
| ||
| 16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).
Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050A.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P050A is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-5 (VG) - E26-91 (VG) | Always | Below 1 Ω |
| E14-4 (E2G) - E26-92 (E2G) | Always | Below 1 Ω |
| E14-5 (VG) or E26-91 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 19.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY |
Replace the mass air flow meter sub-assembly (Click here).
| NEXT | |
| 20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).
Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050A.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050A is output) | B |
|
| ||||
| A | ||
| ||