Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > VSC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch turns off TR(A)C operation and pressing and holding this switch turns off TR(A)C and VSC operation. If VSC operation is turned off, the VSC OFF indicator light will come on.

WIRING DIAGRAM


C239016E01


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V


    Result:

    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE)
    B
    NG (for 2AR-FE)
    C



B
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)
A


4.READ VALUE USING TECHSTREAM (VSC OFF SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRAC/VSC Off Mode
    TR(A)C/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF
    Normal: Normal mode
    TRC OFF: TR(A)C off mode
    Unknown: Unspecified
    VSC OFF: VSC off mode
    -

  1. Using the Techstream, check that the switch condition displayed on the Techstream changes according to VSC OFF switch operation.

    OK:
    The Techstream display changes according to VSC OFF switch operation.



NG
Go to step 6
OK


5.INSPECT COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Perform an Active Test of the combination meter assembly (meter CPU) using the Techstream (Click here).

  1. Check the combination meter assembly.

    OK:
    The VSC OFF indicator light turns on or off in accordance with the Active Test operation.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

6.INSPECT VSC OFF SWITCH


    C239020E01
  1. Turn the ignition switch off.

  1. Disconnect the VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (+) - 3 (E)
    Switch pushed in
    Below 1 Ω
    6 (+) - 3 (E)
    Switch not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (VSC OFF Switch)



NG
REPLACE VSC OFF SWITCH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A49-9 (CSW) - I130-6 (+)
    Always
    Below 1 Ω
    A49-9 (CSW) - Body ground
    Always
    10 kΩ or higher
    I130-3 (E) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)