Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, then fail-safe mode may be functioning.
If power window initialization (Click here) has not been performed, the auto up and down functions will not operate.

WIRING DIAGRAM


B281016E09


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  3. If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (Click here).
  4. When the ECU determines that the power window regulator motor assembly LH (for driver door) has a malfunction, DTC B2311 is stored.

1.READ VALUE USING TECHSTREAM (DRIVER DOOR WINDOW MOTOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / D-Door Motor / Data List.

  1. Read the Data List according to the display on the Techstream.

    D-Door Motor (Power Window Regulator Motor Assembly LH (for Driver Door)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / ON or OFF
    ON: Driver door power window auto switch operated
    OFF: Driver door power window auto switch not operated
    -

    OK:
    On the Techstream screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


2.PERFORM INITIALIZATION (DRIVER DOOR WINDOW MOTOR)
  1. Initialize the power window regulator motor assembly LH (for driver door) (Click here).


NEXT


3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
  1. Check that the driver door power window moves when the auto up and down functions of the power window regulator master switch assembly are operated (Click here).

OK:
Driver door auto up and down functions are normal.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR DRIVER DOOR) (Click here)
OK

END (PROBLEM DUE TO INITIALIZATION FAILURE) 

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B164359E71
  1. Remove the power window regulator master switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (U) - 1 (E)
    Auto UP
    Below 1 Ω
    4 (A) - 1 (E)
    Auto UP
    Below 1 Ω
    5 (D) - 1 (E)
    Auto DOWN
    Below 1 Ω
    4 (A) - 1 (E)
    Auto DOWN
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
  1. Disconnect the power window regulator motor assembly LH (for driver door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K11-4 (A) - K9-4 (AUTO)
    Always
    Below 1 Ω
    K11-4 (A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR DRIVER DOOR) (Click here)