Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump ECU adjust the fuel pump operation speed.

WIRING DIAGRAM


A266397E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. Check whether fuel pump operating sounds can be heard while operating the fuel pump using the Techstream.

    OK:
    Operating sounds can be heard from fuel pump.


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 11
A


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU)


    A256531E01
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N30-1 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Pump Control ECU)



NG
Go to step 9
OK


3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-4 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - FUEL PUMP)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Disconnect the fuel pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-6 (FP) - N11-4 (B)
    Always
    Below 1 Ω
    N30-5 (FP-) - N11-5 (E)
    Always
    Below 1 Ω
    N30-6 (FP) or N11-4 (B) - Body ground
    Always
    10 kΩ or higher
    N30-5 (FP-) or N11-5 (E) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-2 (FPC) - A25-18 (FPC)
    Always
    Below 1 Ω
    N30-2 (FPC) or A25-18 (FPC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END 

9.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - NO. 1 INTEGRATION RELAY)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-1 (+B) - 1C-6
    Always
    Below 1 Ω
    N30-1 (+B) or 1C-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)
  1. Inspect the No. 1 integration relay (EFI MAIN relay) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (EFI MAIN RELAY) (Click here)
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)  

11.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY)


    A240046E04
  1. Remove the fuel pump (Click here).

  1. Clean the fuel pump to completely remove any remaining fuel.

  1. Connect the fuel pump connector.

    CAUTION:
    Confirm that no fuel remains inside or on the outside of the fuel pump.

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty.

  1. Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Techstream Operation
    Specified Condition
    4 (B) - 5 (E)
    Fuel pump control duty: 25%
    3.4 to 4.1 V
    Fuel pump control duty: 80%
    10.0 to 12.5 V

Text in Illustration 
*a
Component with harness connected
(Fuel Pump)
  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Techstream Operation
    Specified Condition
    4 (B) - 5 (E)
    ON (Fuel pump control duty: 90%)
    10.2 to 14.0 V

HINT:
  1. Be sure to measure the voltage with the all connectors connected.
  2. Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).



NG
Go to step 14
OK


12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N30-2 (FPC) - A25-18 (FPC)
    Always
    Below 1 Ω
    N30-2 (FPC) or A25-18 (FPC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.REPLACE FUEL PUMP
  1. Replace the fuel pump (Click here).



NEXT
Go to step 15

14.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END