Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY

FUEL LID LOCK CONTROL CABLE ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made Manual Seat)
(Click here)


4. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made Power Seat)
(Click here)


5. REMOVE FRONT SEAT ASSEMBLY LH (for SIA Made Manual Seat)
(Click here)


6. REMOVE FRONT SEAT ASSEMBLY LH (for SIA Made Power Seat)
(Click here)


7. REMOVE REAR SEAT CUSHION ASSEMBLY


  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.




      B279202E01
    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
      Standard Measurement 
      a
      100 mm (3.94 in.) or less

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.



8. REMOVE REAR SEAT CUSHION LOCK HOOK


    B279203
  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the RH side and the LH side.



9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
  1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

  1. Disconnect the connector.



    B285010
  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear side seatback assembly LH.



10. REMOVE FRONT DOOR SCUFF PLATE LH


    B278977
  1. Disengage the 10 claws and remove the front door scuff plate LH.



11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the front door opening trim weatherstrip.



12. REMOVE REAR DOOR SCUFF PLATE LH


    B278979
  1. Disengage the 6 claws and remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the rear side of the scuff plate.



13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the rear door opening trim weatherstrip.



14. REMOVE LAP BELT OUTER ANCHOR COVER


    B271081
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B271082
  1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.



16. REMOVE CENTER PILLAR LOWER GARNISH LH


    B278989
  1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.



17. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    B280555
  1. Remove the 13 clips and luggage compartment door cover.



18. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
  1. Remove the luggage compartment floor mat.



19. REMOVE SPARE WHEEL COVER ASSEMBLY
  1. Remove the spare wheel cover assembly.



20. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)
  1. Remove the baggage holder net.



21. REMOVE REAR FLOOR FINISH PLATE


    B280564
  1. Remove the 5 clips.



    B280565
  1. Disengage the 4 clips and remove the rear floor finish plate.



22. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    B280637E01
  1. Push the pin and remove the No. 1 luggage compartment trim hook.
    Text in Illustration 
    *1
    Pin



23. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    B280568E01
  1. Remove the clip <A>.
    Text in Illustration 
    *1
    Clip <A>
    *2
    Clip <B>

  1. Remove the 2 clips <B>.



    B288522
  1. Disengage the fastener and remove the luggage compartment inner trim cover LH.



24. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B280595
  1. Remove the screw.



    E227150
  1. Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



    B280598
  1. Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.



25. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


    B280599
  1. Disengage the 2 clamps.



    B280639
  1. Using a clip remover, disengage the clamp and disconnect the wire harness.



    B280600
  1. Using a clip remover, disengage the 2 clamps and remove the 2 scuff plate clips.

  1. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.



  1. w/o Wireless Door Lock Control System:



      B280640
    1. Disconnect the luggage door lock control cable sub-assembly.



    2. B280592
    3. Disengage the 3 clamps and disconnect the luggage door lock control cable sub-assembly.



  1. w/ Wireless Door Lock Control System:



      B280602
    1. Disengage the guide as shown in the illustration.



    2. B280604
    3. Disconnect the luggage door lock control cable sub-assembly.



    4. B280593
    5. Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.



    B287079E01
  1. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <A>



    B288519E01
  1. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <B>



    B287067E01
  1. Pull out the fuel filler opening lid lock retainer with both guides <B and C> aligned with the cutouts.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <C>
    *3
    Guide <B>



    B287069
  1. Disengage the 2 claws and remove the fuel filler opening lid lock retainer.



  1. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.


    B280605E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Luggage Door Lock Control Cable Sub-assembly



  1. Using a knife, cut off the clamp as shown in the illustration.


    B280631E01


    Text in Illustration 
    *1
    Tape
    -
    -
    *a
    Cut
    -
    -

    NOTICE:
    Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

  1. Remove the clamp.

  1. Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.