Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The VVT sensor (for intake camshaft) (VV1, VV2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The camshaft timing gear assembly has a sensor plate for the VVT sensor. When the intake camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the intake camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

Then the ECM uses this data to control fuel injection duration, fuel injection timing and Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit Malfunction One of the following conditions is met:
·

Missing VVT sensor signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or higher (1 trip detection logic).

·

No VVT sensor signal to ECM at engine speed to 600 rpm or higher (1 trip detection logic).

·

No VVT sensor signal to ECM while cranking (2 trip detection logic).


·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


Comes on DTC stored
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the VVT sensor (bank 1) is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

ECM


Comes on DTC stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) The output voltage of the VVT sensor (bank 1) is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

ECM


Comes on DTC stored
P0345 Camshaft Position Sensor "A" Circuit (Bank 2) No VVT sensor signal at engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


Comes on DTC stored
P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) The output voltage of the VVT sensor (bank 2) is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

ECM


Comes on DTC stored
P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) The output voltage of the VVT sensor (bank 2) is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft) circuit

·

VVT sensor (for intake camshaft)

·

ECM


Comes on DTC stored

HINT:

Reference: Inspection using an oscilloscope (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0335).


MONITOR DESCRIPTION

If no pulse signal is transmitted by the VVT sensor (for intake camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) VVT sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR INTAKE CAMSHAFT))
a.
A194108C19
0.208,1.979 0.667,2.26 0.458,0.281 0.208,2.385 0.667,2.667 0.458,0.281 2,2.51 2.281,3.073 false 0.135,0.115 0.385,0.365 0.25,0.25 10 *a 0.323,2.042 0.646,2.208 0.323,0.167 10 E54 0.323,2.448 0.646,2.615 0.323,0.167 10 E60 0.729,2.438 1,2.656 0.271,0.219 10 *2 0.729,2.031 0.969,2.25 0.24,0.219 10 *1 2.26,3.104 2.583,3.271 0.323,0.167 10 VC
*1 Bank 1
*2 Bank 2
*a Front view of wire harness connector
(to VVT Sensor (for Intake Camshaft))


Disconnect the VVT sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E54-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
E60-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E54-1 (VVR+) - E26-81 (VV1+) Always Below 1 Ω
E54-2 (VVR-) - E26-110 (VV1-) Always Below 1 Ω
E60-1 (VVL+) - E26-78 (VV2+) Always Below 1 Ω
E60-2 (VVL-) - E26-110 (VV1-) Always Below 1 Ω
E54-1 (VVR+) or E26-81 (VV1+) - Body ground Always 10 kΩ or higher
E54-2 (VVR-) or E26-110 (VV1-) - Body ground Always 10 kΩ or higher
E60-1 (VVL+) or E26-78 (VV2+) - Body ground Always 10 kΩ or higher
E60-2 (VVL-) or E26-110 (VV1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the VVT sensor (for intake camshaft) installation.

OK:

VVT sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL VVT SENSOR (FOR INTAKE CAMSHAFT)

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)

NG

6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)
a.

Replace the VVT sensor (for intake camshaft).

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the tester on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0340, P0342, P0343, P0345, P0347 or P0348 is output A
DTC is not output B


HINT:

If the engine does not start, replace the ECM.




A

B

END

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E54-3 (VC) - E26-111 (VCV1) Always Below 1 Ω
E60-3 (VC) - E26-111 (VCV1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR