Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate (crankshaft) and a pickup coil. The crank angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft.

The crankshaft position sensor generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit One of the following conditions is met (1 trip detection logic):
·

No crankshaft position sensor signal to ECM while cranking.

·

No crankshaft position sensor signal to ECM while engine running.

·

Missing crankshaft position sensor signal despite VVT sensor signal inputs normal after engine cranked.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or higher.
(b) Starter signal off.
(c) 3 seconds or more have elapsed since starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


Does not come on DTC stored

A207436E11
0.292,1.229 0.542,1.448 0.25,0.219 10 false NE 2.979,1.25 3.323,1.5 0.344,0.25 10 false GND 2.635,0.604 3.25,0.813 0.615,0.208 10 false 5 V/DIV. 2.979,1.813 3.333,2.104 0.354,0.292 10 false GND 2.99,2.198 3.323,2.417 0.333,0.219 10 false GND 1.375,2.51 2.208,2.802 0.833,0.292 10 false 20 ms./DIV. 0.208,1.74 0.531,1.958 0.323,0.219 10 false VV1 0.208,2.031 0.51,2.26 0.302,0.229 10 false VV2 0.292,0.063 2.604,0.458 2.313,0.396 10 false VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveforms is as shown.

·

VV1+ and VV2+ stand for the VVT sensor (for intake camshaft) signal, and NE+ stands for the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause a noisy waveform.



ECM Terminal Name Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) VVT sensor
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

Crankshaft position sensor
·

Crankshaft position sensor output voltage fluctuates while crankshaft is revolving

·

34 crankshaft position sensor signals per crankshaft revolution



CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more.

8.

Enter the following menus: Powertrain / Engine / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0335 or P0339.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255655E06
1.625,0.771 1.74,0.969 0.115,0.198 10 false 1 1.167,0.792 1.573,1.01 0.406,0.219 10 false VVR+ 1.635,1.094 1.75,1.313 0.115,0.219 10 false 2 1.188,1.094 1.563,1.323 0.375,0.229 10 false VVR- 1.635,1.427 1.75,1.656 0.115,0.229 10 false 3 1.333,1.51 1.625,1.74 0.292,0.229 10 false VC 0.219,1.813 2.979,2.073 2.76,0.26 10 false VVT Sensor (for Intake Camshaft of Bank 1) 0.229,1.635 0.531,1.854 0.302,0.219 10 false E54 1.625,2.208 1.729,2.427 0.104,0.219 10 false 1 1.188,2.208 1.552,2.406 0.365,0.198 10 false VVL+ 1.625,2.531 1.729,2.76 0.104,0.229 10 false 2 1.208,2.521 1.552,2.729 0.344,0.208 10 false VVL- 1.625,2.854 1.74,3.052 0.115,0.198 10 false 3 1.333,2.938 1.698,3.177 0.365,0.24 10 false VC 0.208,3.229 2.927,3.479 2.719,0.25 10 false VVT Sensor (for Intake Camshaft of Bank 2) 0.219,3.063 0.531,3.271 0.313,0.208 10 false E60 1.615,3.635 1.708,3.792 0.094,0.156 10 false 1 1.281,3.646 1.594,3.865 0.313,0.219 10 false EX+ 1.625,3.938 1.719,4.094 0.094,0.156 10 false 2 1.302,3.948 1.573,4.177 0.271,0.229 10 false EX- 1.625,4.271 1.719,4.427 0.094,0.156 10 false 3 1.26,4.354 1.552,4.51 0.292,0.156 10 false VC2 0.219,4.656 3.094,4.865 2.875,0.208 10 false VVT Sensor (for Exhaust Camshaft of Bank 1) 0.219,4.49 0.49,4.646 0.271,0.156 10 false E53 1.625,5.063 1.76,5.281 0.135,0.219 10 false 1 1.281,5.073 1.563,5.25 0.281,0.177 10 false EX+ 1.625,5.375 1.74,5.573 0.115,0.198 10 false 2 1.302,5.375 1.552,5.573 0.25,0.198 10 false EX- 1.635,5.708 1.771,5.885 0.135,0.177 10 false 3 1.26,5.802 1.552,5.958 0.292,0.156 10 false VC2 0.219,6.094 3.115,6.292 2.896,0.198 10 false VVT Sensor (for Exhaust Camshaft of Bank 2) 0.219,5.927 0.5,6.146 0.281,0.219 10 false E59 1.625,6.49 1.729,6.667 0.104,0.177 10 false 1 1.635,6.802 1.74,6.99 0.104,0.188 10 false 2 0.417,7.188 2.156,7.385 1.74,0.198 10 false Crankshaft Position Sensor 0.417,7.021 0.688,7.198 0.271,0.177 10 false E72 2.76,6.427 2.854,6.583 0.094,0.156 10 false * 3.688,7.26 4.406,7.469 0.719,0.208 10 false *: Shielded 5.135,7.354 5.469,7.552 0.333,0.198 10 false E26 5.458,7.344 5.823,7.552 0.365,0.208 10 false ECM 4.49,6.802 4.75,7 0.26,0.198 10 false 109 4.813,6.896 5.125,7.094 0.313,0.198 10 false NE- 4.563,6.49 4.771,6.656 0.208,0.167 10 false 76 4.813,6.573 5.135,6.792 0.323,0.219 10 false NE+ 4.573,5.063 4.76,5.25 0.188,0.188 10 false 80 4.813,5.156 5.219,5.313 0.406,0.156 10 false EV2+ 4.563,3.635 4.74,3.792 0.177,0.156 10 false 79 4.813,3.74 5.219,3.896 0.406,0.156 10 false EV1+ 4.563,2.208 4.75,2.396 0.188,0.188 10 false 78 4.813,2.323 5.188,2.542 0.375,0.219 10 false VV2+ 4.49,1.417 4.74,1.573 0.25,0.156 10 false 111 4.802,1.521 5.219,1.729 0.417,0.208 10 false VCV1 4.49,1.094 4.74,1.25 0.25,0.156 10 false 110 4.813,1.188 5.177,1.406 0.365,0.219 10 false VV1- 4.563,0.781 4.74,0.938 0.177,0.156 10 false 81 4.813,0.875 5.198,1.042 0.385,0.167 10 false VV1+

CAUTION / NOTICE / HINT

HINT:
·

After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the VVT sensor.

·

Installation condition of the VVT sensor

·

Installation condition of the camshaft

·

Connection of the VVT sensor connector


·

If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.

·

The engine speed can be checked by using the intelligent tester. To perform the check, follow the procedures below:

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 234 9

e.

Start the engine.


f.

Read the values displayed on the tester while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the tester.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the tester remains zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR
2.INSPECT CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E72-1 - E26-76 (NE+) Always Below 1 Ω
E72-2 - E26-109 (NE-) Always Below 1 Ω
E72-1 or E26-76 (NE+) - Body ground Always 10 kΩ or higher
E72-2 or E26-109 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
B319222E03
1.708,1.563 2.375,1.792 0.667,0.229 10 Clearance 0.469,1.781 0.781,1.979 0.313,0.198 10 OK 2.667,1.781 2.979,1.979 0.313,0.198 10 NG

Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)
a.

Inspect the teeth of the crank angle sensor plate.

OK:

Crank angle sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG