Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a canister to the intake air surge tank assembly for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0443 Evaporative Emission Control System Purge Control Valve Circuit Both of the following conditions (a) and (b) are met (1 trip detection logic):
(a) The target control value and actual control value do not match for 10 seconds or more.
(b) The target control value and actual control value do not match for 80 times or more.
·

Open or short in purge VSV circuit

·

Purge VSV

·

No. 1 integration relay

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A179391E33
0.948,1.573 1.167,1.135 1.167,1.135 1.271,1.135 false 1.521,1.948 1.75,2.125 0.229,0.177 10 false [A] 2.844,1.948 3.073,2.125 0.229,0.177 10 false [B] 3.896,3 4.125,3.177 0.229,0.177 10 false [C] 4.573,1.333 4.802,1.51 0.229,0.177 10 false [D] 5.094,3 5.323,3.177 0.229,0.177 10 false [E] 0.51,2.073 0.885,2.26 0.375,0.188 10 false Idling 4.229,2.521 5.01,2.833 0.781,0.313 10 false 10 minutes or more 2.594,2.521 3.375,2.833 0.781,0.313 10 false 15 minutes or more 1.313,2.521 2.104,2.771 0.792,0.25 10 false Warming up 1.333,1.073 3.365,1.396 2.031,0.323 10 false Between 40 km/h and 60 km/h 0.396,0.448 0.917,0.865 0.521,0.417 10 false Vehicle Speed

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


7.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


8.

Enter the following menus: Powertrain / Engine / DTC [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0443.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



13.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result again [E].


WIRING DIAGRAM

A266384E01
6.284,2.453 6.635,2.637 0.351,0.184 10 ECM 5.675,0.93 5.951,1.114 0.277,0.184 10 E26 5.718,0.75 5.921,0.916 0.203,0.166 10 48 6.02,0.931 6.39,1.115 0.369,0.184 10 PRG 4.528,1.376 5.249,1.541 0.721,0.166 10 Purge VSV 4.528,1.233 4.823,1.399 0.295,0.166 10 E50 1.962,1.748 2.072,1.913 0.11,0.166 10 2 1.759,0.739 1.869,0.904 0.11,0.166 10 1 2.946,1.071 3.63,1.221 0.684,0.15 10 EFI NO. 3 0.536,1.082 1.6,1.285 1.064,0.203 10 EFI-MAIN NO. 1 0.536,2.385 1.114,2.588 0.578,0.203 10 FL MAIN 0.7,3.731 1.173,3.881 0.474,0.15 10 Battery 3.786,0.934 3.982,1.118 0.196,0.184 10 1A 3.786,1.737 3.982,1.921 0.196,0.184 10 1C 1.846,1.936 2.048,2.12 0.203,0.184 10 1E 1.72,0.934 1.913,1.118 0.193,0.184 10 1B 3.828,0.745 3.984,0.929 0.156,0.184 10 8 3.835,1.565 3.991,1.749 0.156,0.184 10 7 2.203,1.758 2.825,1.908 0.622,0.15 10 EFI MAIN 4.302,0.823 4.412,0.988 0.11,0.166 10 1 5.367,0.823 5.477,0.988 0.11,0.166 10 2 5.725,1.57 5.928,1.736 0.203,0.166 10 46 5.675,1.737 5.965,1.921 0.291,0.184 10 A25 6.02,1.744 6.459,1.928 0.439,0.184 10 MREL 2.175,2.156 3.619,2.359 1.444,0.203 10 No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A255866C03
2.004,0.672 2.227,0.122 false 2.227,0.122 2.393,0.122 false 1.694,3.11 1.86,3.262 0.166,0.152 10 *1 2.416,0.031 2.582,0.182 0.166,0.152 10 *2 1.733,1.991 1.551,3.182 false 1.551,3.182 1.66,3.182 false
*1 Purge VSV
*2 Fuel Vapor Feed Hose Assembly (to Canister)


Disconnect the fuel vapor feed hose assembly (on the canister side) of the purge VSV.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

f.

When the purge VSV is operated using the tester, check whether the port of the purge VSV applies suction to your finger.

OK:
Tester Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV (RESISTANCE)
2.INSPECT PURGE VSV (RESISTANCE)

Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
a.
A194112C42
0.521,2.031 1.01,2.323 0.49,0.292 0.25,0.198 0.438,0.385 0.188,0.188 10 false *a 0.656,2.094 0.948,2.271 0.292,0.177 10 false E50
*a Front view of wire harness connector
(to Purge VSV)


Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E50-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E50-2 - E26-48 (PRG) Always Below 1 Ω
E50-2 or E26-48 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
a.

Disconnect the purge VSV connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E50-1 - 1A-8 Always Below 1 Ω
E50-1 or 1A-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR