Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  P0020  Camshaft Position "A" Actuator Circuit (Bank 2)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A209140E60
2.563,4.573 2.844,4.271 2.844,4.271 3.615,4.271 false 3.177,4.781 3.323,5.01 3.323,5.01 3.854,5.01 false 5.25,0.813 6.021,1.021 0.771,0.208 10 false VVT Sensor 4.771,1.323 6.5,1.479 1.729,0.156 10 false Crankshaft Position Sensor 0.073,0.094 0.948,0.292 0.875,0.198 10 false VVT System: 2.333,1.958 3.615,2.135 1.281,0.177 10 false Target Valve Timing 2.333,1.292 3.615,1.469 1.281,0.177 10 false Actual Valve Timing 2.688,2.698 3.406,2.875 0.719,0.177 10 false Correction 2.823,3.563 3.229,3.74 0.406,0.177 10 false ECM 1.604,3.792 4.531,3.979 2.927,0.188 10 false Camshaft Timing Oil Control Valve Assembly 0.167,2.688 0.865,2.865 0.698,0.177 10 false Duty-cycle 4.531,1.854 6.74,2.073 2.208,0.219 10 false Mass Air Flow Meter Sub-assembly 4.479,2.854 6.781,3.052 2.302,0.198 10 false Engine Coolant Temperature Sensor 4.865,2.375 6.396,2.542 1.531,0.167 10 false Throttle Position Sensor 4.917,3.385 6.354,3.563 1.438,0.177 10 false Vehicle Speed Sensor 0.313,4.271 1.677,4.479 1.365,0.208 10 false Engine Oil Pressure 3.667,4.219 7.063,4.406 3.396,0.188 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.885,4.917 4.99,5.104 1.104,0.188 10 false Intake Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 Camshaft Position "A" Actuator Circuit (Bank 1) Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 1) circuit

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 1)

·

ECM


Comes on DTC stored
P0020 Camshaft Position "A" Actuator Circuit (Bank 2) Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 2) circuit

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 2)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly (for intake camshaft) circuit. If the camshaft timing oil control valve assembly duty-cycle is excessively high or low while the ignition switch is ON or the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P0010 or P0020.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255389E17
0.479,1.656 0.771,1.813 0.292,0.156 10 false E58 0.479,1.823 3.302,2.156 2.823,0.333 10 false Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft of Bank 1) 0.479,3.635 0.771,3.792 0.292,0.156 10 false E62 0.479,3.802 3.323,4.135 2.844,0.333 10 false Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft of Bank 2) 5.156,0.479 5.552,0.719 0.396,0.24 10 false 35 5.229,1.229 5.406,1.385 0.177,0.156 10 false 5 5.156,2.438 5.51,2.688 0.354,0.25 10 false 34 5.229,3.198 5.406,3.354 0.177,0.156 10 false 4 5.427,0.469 6.135,0.76 0.708,0.292 10 false OC1+ 5.427,1.229 6.125,1.448 0.698,0.219 10 false OC1- 5.427,2.438 6.021,2.792 0.594,0.354 10 false OC2+ 5.427,3.188 5.969,3.49 0.542,0.302 10 false OC2- 5.969,4.083 6.583,4.396 0.615,0.313 10 false ECM 5.656,4.083 6.26,4.396 0.604,0.313 10 false E26 1.458,0.469 1.635,0.625 0.177,0.156 10 false 1 1.458,1.208 1.635,1.365 0.177,0.156 10 false 2 1.458,2.438 1.635,2.594 0.177,0.156 10 false 1 1.458,3.177 1.635,3.333 0.177,0.156 10 false 2

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0010 is output, check the VVT system (for intake camshaft of bank 1) circuit.

·

If DTC P0020 is output, check the VVT system (for intake camshaft of bank 2) circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0010 OR P0020)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTC after recording the freeze frame data and DTC.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and wait 5 seconds.


g.

Turn the tester on.


h.

Enter the following menus: Powertrain / Engine / DTC.


i.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0010 or P0020 is output A
DTC is not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake camshaft).

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E58-1 - E26-35 (OC1+) Always Below 1 Ω
E58-2 - E26-5 (OC1-) Always Below 1 Ω
E62-1 - E26-34 (OC2+) Always Below 1 Ω
E62-2 - E26-4 (OC2-) Always Below 1 Ω
E58-1 or E26-35 (OC1+) - Body ground Always 10 kΩ or higher
E58-2 or E26-5 (OC1-) - Body ground Always 10 kΩ or higher
E62-1 or E26-34 (OC2+) - Body ground Always 10 kΩ or higher
E62-2 or E26-4 (OC2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR