Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P1660  VSV for AICVS Circuit  


DESCRIPTION

The air cleaner is equipped with 2 inlets, one of which is opened or closed by the air intake control valve. This system reduces intake noise and increases engine power at low-to-high engine speed ranges.

When the engine is operating in the low-to-mid speed range, this control operates the air intake control valve to close one of the air cleaner inlets. When the engine speed is higher than 3600 rpm and the opening angle of the throttle valve is more than 60°, the ECM activates the vacuum switching valve (for air intake control valve) and opens the air intake control valve.

A212427E07
5.865,0.25 5.969,0.25 5.969,0.25 6.063,1 false 1.75,0.083 1.583,0.083 1.583,0.083 1.5,0.885 false 0.927,1.75 1.281,2.281 1.281,2.281 0.74,1.969 false 1.052,0.104 1.135,0.104 1.135,0.104 1.219,1.01 false 2.125,1.583 1.333,1.583 false 3.781,0.635 4.698,0.99 0.917,0.354 10 false Throttle Valve Opening Angle 2.198,1.51 3.333,2.208 1.135,0.698 10 false Air Intake Control Valve (AICV) 1.323,2.229 2.406,2.583 1.083,0.354 10 false Air Cleaner Inlet 1.802,0.021 2.75,0.375 0.948,0.354 10 false Vacuum Tank 0.073,0.042 1.042,0.76 0.969,0.719 10 false Vacuum Switching Valve (for Air Intake Control Valve) 5.188,2.469 6.125,2.646 0.938,0.177 10 false Engine Speed 5.333,2.198 5.99,2.375 0.656,0.177 10 false 3600 rpm 3.219,0.167 5.896,0.354 2.677,0.188 10 false AICV Open (Vacuum Switching Valve: ON) 4.5,1.438 4.854,1.615 0.354,0.177 10 false 60°

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1660 VSV for AICVS Circuit The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
1.

Voltage of terminal air intake control valve of the ECM is low when the VSV is off

2.

The engine has been started


·

Open or short in air intake control valve circuit

·

Air intake control valve

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A268233E04
5.667,1.198 6.01,1.344 0.344,0.146 10 false AICV 5.667,2.948 6.094,3.094 0.427,0.146 10 false MREL 6.031,3.896 6.365,4.042 0.333,0.146 10 false ECM 5.323,1.188 5.594,1.333 0.271,0.146 10 false E26 5.323,2.938 5.615,3.146 0.292,0.208 10 false A25 5.375,2.76 5.552,2.906 0.177,0.146 10 false 46 5.375,1 5.552,1.146 0.177,0.146 10 false 46 3.625,1.458 3.896,1.604 0.271,0.146 10 false A9 3.625,1.615 5.417,2.156 1.792,0.542 10 false Vacuum Switching Valve (for Air Intake Control Valve) 3.813,1.094 3.917,1.24 0.104,0.146 10 false 1 5.052,1.104 5.156,1.25 0.104,0.146 10 false 2 3.177,1.188 3.385,1.333 0.208,0.146 10 false 1C 3.177,1.677 3.427,1.823 0.25,0.146 10 false 1C 3.229,1 3.323,1.146 0.094,0.146 10 false 3 3.229,1.49 3.323,1.635 0.094,0.146 10 false 7 1.25,1.188 1.469,1.333 0.219,0.146 10 false 1B 1.302,1 1.396,1.146 0.094,0.146 10 false 1 1.323,2.229 1.531,2.375 0.208,0.146 10 false 1E 1.448,2.052 1.542,2.198 0.094,0.146 10 false 2 2.344,1.323 2.99,1.469 0.646,0.146 10 false EFI NO. 3 1.667,1.938 2.292,2.083 0.625,0.146 10 false EFI MAIN 1.708,2.458 3.198,2.708 1.49,0.25 10 false No. 1 Integration Relay 0.458,1.688 1.115,2.01 0.656,0.323 10 false EFI-MAIN NO. 1 0.583,3.396 1.042,3.646 0.458,0.25 10 false Battery 0.479,2.521 1.052,2.667 0.573,0.146 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR AICS)
a.
A204525C01
0.49,1.458 0.313,1.646 false 0.688,1.344 0.938,1.781 false 1.958,1.448 1.865,1.646 false 2.156,1.354 2.552,1.792 false 1.417,1.083 1.479,0.781 false 1.479,0.781 1.583,0.781 false 2.927,1.25 3,1.49 false 3,1.49 3.083,1.49 false 0.313,0.188 0.708,0.667 0.396,0.479 10 *a 1.896,0.188 2.26,0.51 0.365,0.323 10 *b 0.771,0.594 0.969,0.76 0.198,0.167 10 *1 2.448,1.771 2.604,1.938 0.156,0.167 10 *2 0.875,1.771 1.031,1.938 0.156,0.167 10 *2 1.76,1.635 1.917,1.802 0.156,0.167 10 *3 0.208,1.635 0.365,1.813 0.156,0.177 10 *3 2.208,0.656 2.406,0.833 0.198,0.177 10 *1 1.604,0.698 1.76,0.854 0.156,0.156 10 *4 3.104,1.406 3.26,1.563 0.156,0.156 10 *4
*1 Air
*2 Port E
*3 Port F
*4 Air Filter
*a Vacuum Switching Valve is On
*b Vacuum Switching Valve is Off


Disconnect the vacuum hose (Port F) from the vacuum switching valve (for air intake control valve).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for AICS.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for AICS
50004 234 75

f.

Check the operation of the vacuum switching valve (for air intake control valve) when the vacuum switching valve (for air intake control valve) is operated using the tester.

Standard:
Tester Operation Specified Condition
ON Air from port E flows out through port F
OFF Air from port E flows out through the air filter



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE)
2.INSPECT VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE)
a.

Inspect the vacuum switching valve (for air intake control valve).

Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>VACUUM SWITCHING VALVE(for Intake Air Control System)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE))

NG

REPLACE VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE))
a.
A203087C02
0.552,1.073 1.01,1.354 0.458,0.281 0.25,0.167 0.698,0.469 0.448,0.302 10 *a 0.719,1.135 1.146,1.365 0.427,0.229 10 A9
*a Front view of wire harness connector
(to Vacuum Switching Valve (for Air Intake Control Valve))


Disconnect the vacuum switching valve (for air intake control valve) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A9-1 - Body ground ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE) - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE))
4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE) - ECM)
a.

Disconnect the vacuum switching valve (for air intake control valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A9-2 - E26-46 (AICV) Always Below 1 Ω
A9-2 or E26-46 (AICV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - VACUUM SWITCHING VALVE (FOR AIR INTAKE CONTROL VALVE))
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the vacuum switching valve (for air intake control valve) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-3 - A9-1 Always Below 1 Ω
1C-3 or A9-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR