Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  P0023  Camshaft Position "B" Actuator Circuit / Open (Bank 2)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A209140E59
5.248,0.815 6.029,1.027 0.782,0.212 10 VVT Sensor 4.773,1.325 6.496,1.486 1.724,0.161 10 Crankshaft Position Sensor 0.072,0.015 0.944,0.215 0.873,0.2 10 VVT System: 2.337,1.96 3.614,2.135 1.277,0.175 10 Target Valve Timing 2.337,1.288 3.614,1.463 1.277,0.175 10 Actual Valve Timing 2.687,2.696 3.401,2.871 0.714,0.175 10 Correction 2.826,3.54 3.228,3.715 0.402,0.175 10 ECM 1.602,3.792 4.402,3.976 2.799,0.185 10 Camshaft Timing Oil Control Valve Assembly 0.17,2.69 0.865,2.865 0.695,0.175 10 Duty-cycle 4.53,1.849 6.735,2.072 2.206,0.222 10 Mass Air Flow Meter Sub-assembly 4.483,2.856 6.781,3.055 2.298,0.199 10 Engine Coolant Temperature Sensor 4.868,2.344 6.402,2.512 1.534,0.168 10 Throttle Position Sensor 4.917,3.361 6.354,3.541 1.437,0.18 10 Vehicle Speed Sensor 0.317,4.27 1.683,4.475 1.366,0.205 10 Engine Oil Pressure 4.364,4.217 6.437,4.563 2.073,0.346 10 VVT Controller (Camshaft Timing Exhaust Gear Assembly) 3.887,4.918 5.183,5.102 1.296,0.184 10 Exhaust Camshaft 2.566,4.571 2.846,4.275 2.846,4.275 4.311,4.275 false 3.181,4.782 3.323,5.009 3.323,5.009 3.856,5.009 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1) Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) circuit

·

Camshaft timing oil control valve assembly (for exhaust camshaft of bank 1)

·

ECM


Comes on DTC stored
P0023 Camshaft Position "B" Actuator Circuit / Open (Bank 2) Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) circuit

·

Camshaft timing oil control valve assembly (for exhaust camshaft of bank 2)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly (for exhaust camshaft) circuit. If the camshaft timing oil control valve assembly duty-cycle is excessively high or low while the ignition switch is ON or the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P0013 or P0023.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255389E16
0.479,1.646 0.771,1.802 0.292,0.156 10 false E57 0.479,1.813 3.302,2.146 2.823,0.333 10 false Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft of Bank 1) 0.479,3.625 0.771,3.781 0.292,0.156 10 false E61 0.479,3.792 3.323,4.125 2.844,0.333 10 false Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft of Bank 2) 5.156,0.479 5.333,0.635 0.177,0.156 10 false 33 5.229,1.229 5.406,1.385 0.177,0.156 10 false 3 5.156,2.438 5.333,2.594 0.177,0.156 10 false 32 5.229,3.198 5.406,3.354 0.177,0.156 10 false 2 5.427,0.469 5.844,0.667 0.417,0.198 10 false OE1+ 5.427,1.229 5.844,1.427 0.417,0.198 10 false OE1- 5.427,2.438 5.844,2.635 0.417,0.198 10 false OE2+ 5.427,3.188 5.844,3.385 0.417,0.198 10 false OE2- 5.938,4.125 6.271,4.323 0.333,0.198 10 false ECM 5.635,4.125 5.948,4.323 0.313,0.198 10 false E26 1.458,0.479 1.635,0.635 0.177,0.156 10 false 1 1.458,1.208 1.635,1.365 0.177,0.156 10 false 2 1.458,2.438 1.635,2.594 0.177,0.156 10 false 1 1.458,3.177 1.635,3.333 0.177,0.156 10 false 2

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is output, check the VVT system (for exhaust camshaft of bank 1) circuit.

·

If DTC P0023 is output, check the VVT system (for exhaust camshaft of bank 2) circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0013 OR P0023)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTC after recording the freeze frame data and DTC.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and wait 5 seconds.


g.

Turn the tester on.


h.

Enter the following menus: Powertrain / Engine / DTC.

Powertrain > Engine > Trouble Codes
50001 234

i.

Read the DTCs.


Result:
Result Proceed to
DTC P0013 or P0023 is output A
DTC is not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for exhaust camshaft).

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E57-1 - E26-33 (OE1+) Always Below 1 Ω
E57-2 - E26-3 (OE1-) Always Below 1 Ω
E61-1 - E26-32 (OE2+) Always Below 1 Ω
E61-2 - E26-2 (OE2-) Always Below 1 Ω
E57-1 or E26-33 (OE1+) - Body ground Always 10 kΩ or higher
E57-2 or E26-3 (OE1-) - Body ground Always 10 kΩ or higher
E61-1 or E26-32 (OE2+) - Body ground Always 10 kΩ or higher
E61-2 or E26-2 (OE2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR