Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The VVT sensor (for exhaust camshaft) (EV1, EV2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The exhaust camshaft has a timing rotor for the VVT sensor. When the exhaust camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

Then the ECM uses this data to control fuel injection duration, fuel injection timing and the Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0365 Camshaft Position Sensor "B" Circuit (Bank 1) No exhaust VVT sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

Exhaust camshaft

·

Valve timing

·

ECM


Comes on DTC stored
P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) The output voltage of the exhaust VVT sensor (bank 1) is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored
P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) The output voltage of the exhaust VVT sensor (bank 1) is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored
P0390 Camshaft Position Sensor "B" Circuit (Bank 2) No exhaust VVT sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

Exhaust camshaft

·

Valve timing

·

ECM


Comes on DTC stored
P0392 Camshaft Position Sensor "B" Circuit Low Input (Bank 2) The output voltage of the exhaust VVT sensor (bank 2) is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored
P0393 Camshaft Position Sensor "B" Circuit High Input (Bank 2) The output voltage of the exhaust VVT sensor (bank 2) is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored

Reference: Inspection using an oscilloscope.

A207435E02
0.287,1.201 0.521,1.362 0.233,0.161 10 NE 2.986,1.201 3.322,1.362 0.337,0.161 10 GND 2.631,0.697 3.189,0.858 0.559,0.161 10 5 V/DIV. 2.986,1.754 3.322,1.914 0.337,0.161 10 GND 2.986,2.144 3.322,2.304 0.337,0.161 10 GND 1.28,2.462 2.067,2.622 0.786,0.161 10 20 ms./DIV. 0.2,1.717 0.504,1.877 0.304,0.161 10 EV1 0.2,2.003 0.504,2.164 0.304,0.161 10 EV2 0.254,0.122 2.575,0.508 2.321,0.386 10 EV1, EV2 and NE Signal Waveforms

HINT:

EV1+ and EV2+ stand for the VVT sensor (for exhaust camshaft) signal, and NE+ stands for the crankshaft position sensor signal.


ECM Terminal Name Between NE+ and NE-
Between EV1+ and VV1-
Between EV2+ and VV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

MONITOR DESCRIPTION

If no pulse signal is transmitted by the VVT sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the exhaust camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) VVT sensor (for exhaust camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0365, P0367, P0368, P0390, P0392 or P0393.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR EXHAUST CAMSHAFT))
a.
A194108C20
0.219,2.125 0.635,2.365 0.417,0.24 0.219,2.5 0.635,2.74 0.417,0.24 2,2.521 2.479,3.031 false 0.302,2.167 0.573,2.333 0.271,0.167 10 E53 0.688,2.156 0.844,2.323 0.156,0.167 10 *1 0.302,2.542 0.573,2.708 0.271,0.167 10 E59 0.688,2.531 0.875,2.698 0.188,0.167 10 *2 0.135,0.146 0.406,0.375 0.271,0.229 10 *a 2.448,3.063 2.74,3.25 0.292,0.188 10 VC2
*1 Bank 1
*2 Bank 2
*a Front view of wire harness connector
(to VVT Sensor (for Exhaust Camshaft))


Disconnect the VVT sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E53-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.5 V
E59-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E53-1 (EX+) - E26-79 (EV1+) Always Below 1 Ω
E53-2 (EX-) - E26-110 (VV1-) Always Below 1 Ω
E59-1 (EX+) - E26-80 (EV2+) Always Below 1 Ω
E59-2 (EX-) - E26-110 (VV1-) Always Below 1 Ω
E53-1 (EX+) or E26-79 (EV1+) - Body ground Always 10 kΩ or higher
E53-2 (EX-) or E26-110 (VV1-) - Body ground Always 10 kΩ or higher
E59-1 (EX+) or E26-80 (EV2+) - Body ground Always 10 kΩ or higher
E59-2 (EX-) or E26-110 (VV1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR EXHAUST CAMSHAFT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR EXHAUST CAMSHAFT))
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the VVT sensor (for exhaust camshaft) installation.

OK:

VVT sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL VVT SENSOR (FOR EXHAUST CAMSHAFT)

4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Inspect the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the exhaust camshaft.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

6.REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT)

NG

6.REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT)
a.

Replace the VVT sensor (for exhaust camshaft).

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367, P0368, P0390, P0392 OR P0393)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367, P0368, P0390, P0392 OR P0393)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the tester on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0365, P0367, P0368, P0390, P0392 or P0393 is output A
DTC is not output B


HINT:

If the engine does not start, replace the ECM.




A

B

END

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E53-3 (VC2) - E26-111 (VCV1) Always Below 1 Ω
E59-3 (VC2) - E26-111 (VCV1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR