Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  U0101  Lost Communication with TCM  


MONITOR DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communication with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine speed, required engine torque, warning indicators in the combination meter assembly, DTCs and other data. The ECM sends signals to the TCM concerning engine speed, opening angle of the throttle valve, temperature of intake air, temperature of engine coolant, engine torque and other data. If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN system, illuminate the MIL and store a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0101 Lost Communication with TCM

All of the following conditions are met for 1.25 seconds (1 trip detection logic):

1.

Ignition switch ON

2.

Battery voltage 10.5 V or higher

3.

No communication between ECM and TCM



·

ECM to TCM circuit

·

TCM

·

ECM


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: U0101.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A192819E17
1.385,1.656 1.583,1.844 0.198,0.188 10 false 18 0.656,2.927 0.854,3.083 0.198,0.156 10 false E7 0.979,0.938 1.344,1.125 0.365,0.188 10 false CAN- 6.073,0.948 6.438,1.135 0.365,0.188 10 false CAN- 1.406,0.865 1.552,1.052 0.146,0.188 10 false 7 2.323,1.74 3.698,1.927 1.375,0.188 10 false from EFI MAIN Relay 3.76,2.104 4.563,2.292 0.802,0.188 10 false from Battery 6.125,2.927 6.438,3.083 0.313,0.156 10 false E26 5.875,0.865 5.979,1.052 0.104,0.188 10 false 1 6.073,1.385 6.552,1.573 0.479,0.188 10 false CAN+ 5.823,1.292 6.01,1.479 0.188,0.188 10 false 31 0.948,1.375 1.354,1.563 0.406,0.188 10 false CAN+ 1.396,1.302 1.542,1.49 0.146,0.188 10 false 6 0.958,2.125 1.365,2.313 0.406,0.188 10 false BATT 1.146,1.719 1.365,1.906 0.219,0.188 10 false +B 0.656,3.083 0.99,3.229 0.333,0.146 10 false TCM 6.125,3.083 6.521,3.271 0.396,0.188 10 false ECM 2.646,2.281 3.313,2.469 0.667,0.188 10 false EFI NO. 1 1.396,2.021 1.542,2.208 0.146,0.188 10 false 1 1.125,2.5 1.365,2.688 0.24,0.188 10 false E1 1.406,2.417 1.552,2.604 0.146,0.188 10 false 8

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC U0101 is output A
DTC U0101 and other DTCs are output B


HINT:

If any DTCs other than U0101 are output, troubleshoot those DTCs first.




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)
a.
A194125C01
0.198,1.365 0.615,1.604 0.417,0.24 1.531,2.365 1.219,1.302 false 1.49,3.135 1.188,2.667 false 1.094,2.479 0.823,3.125 false 0.25,0.188 0.927,0.677 0.677,0.49 10 *a 0.302,1.396 1.031,1.792 0.729,0.396 10 E7 0.958,1.115 1.635,1.49 0.677,0.375 10 BATT 1.448,3.135 2,3.427 0.552,0.292 10 +B 0.656,3.156 1.01,3.396 0.354,0.24 10 E1
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-1 (BATT) - E7-8 (E1) Always 11 to 14 V
E7-18 (+B) - E7-8 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-6 (CAN+) - E26-31 (CAN+) Always Below 1 Ω
E7-7 (CAN-) - E26-1 (CAN-) Always Below 1 Ω
E7-6 (CAN+) or E26-31 (CAN+) - Body ground Always 10 kΩ or higher
E7-7 (CAN-) or E26-1 (CAN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TCM

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON.


g.

Turn the tester on.


h.

Wait for 5 seconds or more.


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC U0101 is output B




A

END

B