Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL OIL SEAL
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0074470 DIFFERENTIAL OIL SEAL A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN AUTOMATIC TRANSAXLE FLUID

a.

for LHD:

i.

Remove the engine under cover LH and front fender apron seal LH.



b.

for RHD:

i.

Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.



c.
C201682

Remove the refill plug and gasket from the automatic transaxle assembly.


d.
C239660

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.


e.
C201684
1.22,2.592 1.376,2.756 0.155,0.165 10 *1 1.22,3.134 1.384,3.296 0.164,0.162 10 *2 0.659,3.847 0.84,4.037 0.181,0.19 10 *a 1.205,2.679 0.835,2.679 false 0.603,3.928 0.414,3.928 0.414,3.928 0.713,3.129 false 1.205,3.214 0.83,3.214 false
*1 No. 1 Transmission Oil Filler Tube
*2 Hexagon Socket Wrench
*a Overflow Plug Hole


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle assembly.


f.

Drain automatic transaxle fluid from the automatic transaxle oil pan sub-assembly.


g.
C201684
1.22,2.592 1.376,2.756 0.155,0.165 10 *1 1.22,3.134 1.384,3.296 0.164,0.162 10 *2 0.659,3.847 0.84,4.037 0.181,0.19 10 *a 1.205,2.679 0.835,2.679 false 0.603,3.928 0.414,3.928 0.414,3.928 0.713,3.129 false 1.205,3.214 0.83,3.214 false
*1 No. 1 Transmission Oil Filler Tube
*2 Hexagon Socket Wrench
*a Overflow Plug Hole


Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


h.
C239660

Using a 6 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transaxle oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 29 ft.*lbf)


i.
C201682

Temporarily install the gasket and refill plug to the automatic transaxle assembly.


Hide 43457 3.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 31105H 4.REMOVE TRANSAXLE CASE OIL SEAL

a.
C133598
1.449,1.875 1.751,2.039 0.301,0.164 10 SST 1.615,1.544 1.615,1.851 false

Using SST, tap out the transaxle case oil seal.

SST
09308-00010  


Hide 31105D 5.REMOVE FRONT TRANSAXLE CASE OIL SEAL

a.
C133597
1.058,0.194 1.415,0.381 0.357,0.186 10 SST 1.234,0.829 1.234,0.361 false

Using SST, tap out the front transaxle case oil seal.

SST
09308-00010  


Hide 31105H 6.INSTALL TRANSAXLE CASE OIL SEAL

a.
C274794
1.198,1.813 1.823,2.677 1.823,2.677 1.448,1.906 true 1.979,1.313 1.385,0.302 1.385,0.302 2.104,0.896 true 1.75,2.719 2.208,2.917 0.458,0.198 10 SST 1.083,0.208 1.542,0.406 0.458,0.198 10 SST

Using SST and a hammer, tap in a new transaxle case oil seal.

SST
09316-10010  
09950-70010  (09951-07100)

Oil seal driven in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the oil seal is installed in the correct direction.



b.

Coat the lip of the transaxle case oil seal with MP grease.


Hide 31105D 7.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C188729
1.563,2.073 1.563,2.646 false 2.146,0.771 2.146,1.146 false 1.396,2.667 1.719,2.823 0.323,0.156 10 false SST 1.969,1.146 2.292,1.302 0.323,0.156 10 false SST

Using SST and a hammer, tap in a new front transaxle case oil seal.

SST
09316-60011  (09316-00011)

Oil seal driven in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the oil seal is installed in the correct direction.



b.

Coat the lip of the front transaxle case oil seal with MP grease.


Hide 43457 8.INSTALL DRIVE SHAFT BEARING BRACKET

Hide 43420G 9.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH