Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY › 2012.02–2015.04
RM2030EQ _54 Brake _014654 PARKING BRAKE _0074526 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL PARKING BRAKE SHOE LEVER

a.

for PBR Made:

i.

Install the parking brake shoe lever.



Hide 2.INSTALL DUST COVER

a.

for PBR Made:

i.
C141965

Install the dust cover to the parking brake shoe lever as shown in the illustration.


ii.
C240921

Using an air riveter or a hand riveter with a nose piece, install the boot retainer on the back plate with 2 new rivets.

HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B130465

Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B130466

Confirm that the rivets are seated properly against the boot retainer.

·

Do not tilt the riveter when installing the rivet onto the boot retainer.

·

Do not leave any space between the rivet head and boot retainer.

·
B130467

Do not leave any space between the boot retainer and the parking brake plate sub-assembly. Firmly hold the 2 items together while installing the rivet.





Hide 3.INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY

a.

for PBR Made:

i.

Install the parking brake shoe plate sub-assembly.



Hide 4.INSTALL DUST PLATE

a.

for PBR Made:

i.

Install the dust plate to the parking brake plate sub-assembly.



Hide 42450B 5.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Hide 89516D 6.CONNECT SKID CONTROL SENSOR WIRE

Hide 7.INSTALL PARKING BRAKE SHOE HOLD PLATE

a.

for PBR Made:

i.
C240919

Install the parking brake shoe hold plate with a new parking brake shoe hold bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)



Hide 8.INSTALL ADJUSTMENT PAWL

a.

for PBR Made:

i.
C240918

Install the adjustment pawl.



Hide 9.INSTALL NUT AND SCREW ADJUSTING ASSEMBLY

a.

for PBR Made:

i.
C247506C01
0.99,1.354 0.99,1.344 false
V100145

High Temperature Grease


Apply high temperature grease to the parking brake plate sub-assembly as shown in the illustration.


ii.

Install the nut and screw adjusting assembly, parking brake tappet and parking brake push rod.



Hide 46430 10.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 11.INSTALL PARKING BRAKE SHOE ASSEMBLY

a.

for PBR Made:

i.
C247505

Install the parking brake shoe assembly as shown in the illustration.

NOTICE:

There should be no oil or grease on the friction surface of the lining and disc.




Hide 47456A 12.INSTALL PARKING BRAKE SHOE GUIDE PLATE

a.

for ADVICS Made:

i.
C240103

Install the parking brake shoe guide plate with the parking brake shoe guide plate set bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)



Hide 13.APPLY HIGH TEMPERATURE GREASE

a.

for ADVICS Made:

i.
C240104C02
0.958,0.542 0.958,0.531 false
V100155

High Temperature Grease


Apply high temperature grease to the areas of the parking brake plate which make contact with the shoes as shown in the illustration.



Hide 47447E 14.INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN

a.

for ADVICS Made Front Side:

i.

Install the 2 parking brake shoe hold down spring cups, parking brake shoe hold down spring and parking brake shoe hold down spring pin.



b.

for ADVICS Made Rear Side:

i.

Install the 2 parking brake shoe hold down spring cups, parking brake shoe hold down spring and parking brake shoe hold down spring pin.



Hide 47612 15.INSTALL PARKING BRAKE SHOE LEVER

a.

for ADVICS Made:

i.
C240105C02
1.635,0.479 1.635,0.49 false
V100137

High Temperature Grease


Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.


ii.

Temporarily install the parking brake shoe lever to the No. 2 parking brake shoe assembly with a new parking brake shoe type C washer.


iii.
C240106

Using a feeler gauge, measure the clearance between the No. 2 parking brake shoe assembly and parking brake shoe lever.

Standard clearance:

Less than 0.35 mm (0.0137 in.)


If the clearance is not as specified, replace the parking brake shoe shim with one of the correct size.

Parking Brake Shoe Shim:
Part No. Shim Thickness
90564-09184 0.3 mm (0.0118 in.)
90564-09185 0.6 mm (0.0236 in.)
90564-09186 0.9 mm (0.0354 in.)



iv.

Select a parking brake shoe shim and install it and the parking brake shoe type C washer.


v.
C132646

Using a pair of pliers, squeeze together the ends of the parking brake shoe type C washer.


vi.

Check that the parking brake shoe lever moves smoothly.



Hide 47612 16.CONNECT PARKING BRAKE SHOE LEVER

a.

for ADVICS Made:

i.
C240148

Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever.



Hide 46550E 17.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)

a.

for ADVICS Made:

i.

Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.



Hide 46580 18.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY

a.

for ADVICS Made:

i.

Install the No. 1 parking brake shoe assembly to the parking brake shoe return tension spring.



Hide 47406A 19.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

a.

for ADVICS Made:

i.
C236276C02
2.615,0.969 2.604,0.958 false
V100155

High Temperature Grease


Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.


ii.

Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.


iii.
C240894C02
1.594,1.583 1.583,1.583 false
V100137

High Temperature Grease


Apply high temperature grease to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly as shown in the illustration.


iv.
C240149

Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the parking brake plate.

NOTICE:

Make sure that the parking brake shoe lever does not separate from the No. 2 parking brake shoe assembly.




Hide 46590 20.CONNECT NO. 2 PARKING BRAKE SHOE ASSEMBLY

a.

for ADVICS Made:

i.
C239427

Engage the claw of the parking brake shoe hold down spring cup to the No. 2 parking brake shoe assembly.



Hide 46580 21.CONNECT NO. 1 PARKING BRAKE SHOE ASSEMBLY

a.

for ADVICS Made:

i.
C239426

Engage the claw of the parking brake shoe hold down spring cup to the No. 1 parking brake shoe assembly.



Hide 47613D 22.INSTALL PARKING BRAKE SHOE STRUT COMPRESSION SPRING

a.

for ADVICS Made:

i.

Install the parking brake shoe strut compression spring.



Hide 47614 23.INSTALL PARKING BRAKE SHOE STRUT

a.

for ADVICS Made:

i.

Install the parking brake shoe strut.


ii.
C240150

Install the No. 1 parking brake shoe assembly.



Hide 46550G 24.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)

a.

for ADVICS Made Front Side:

i.

Install the parking brake shoe return tension spring.



b.

for ADVICS Made Rear Side:

i.

Install the parking brake shoe return tension spring.



Hide 25. CHECK PARKING BRAKE INSTALLATION

a.

for ADVICS Made:

i.

Check that each part is installed properly.

C264481C03
0.719,0.51 1.094,0.75 0.375,0.24 12 *A 3.979,0.531 4.354,0.771 0.375,0.24 12 *B
*A LH Side *B RH Side
V100135

Front of the Vehicle - -


NOTICE:

There should be no oil or grease on the friction surfaces of the shoe linings or discs.




Hide 26.INSPECT REAR AXLE HUB BEARING LOOSENESS

Hide 27.INSPECT REAR AXLE HUB RUNOUT

Hide 42431 28.INSTALL REAR DISC

Hide 42491 29.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 30.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Hide 31.INSTALL REAR WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 32.ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for LHD)

Hide 33.ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for RHD)