1.RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
Start up the engine.
Operate the cooler compressor at the conditions shown below:
| Item | Condition |
|---|---|
| Engine Speed | Idling |
| Operating Time | 3 minutes or more |
| A/C Switch Status | ON |
| Blower Switch Status | HI |
| Set Temperature | MAX COOL |
This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.
Do not need to operate the cooler compressor if the A/C does not operate because of compressor lock etc.
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.
2.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.
HFC-134a (R134a)
| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100 g (3.5 oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| *i | +/- 50 g (+/- 1.80 oz.) | - | - |
450 to 550 g (15.9 to 19.4 oz.)
Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.
The refrigerant amount should be checked by quantity (weight).
Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.
3.WARM UP ENGINE
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing air conditioning system lines (including the compressor).
4.INSPECT FOR REFRIGERANT LEAK
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
Ignition switch off.
Secure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).
Repeat the inspection 2 or 3 times.
Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.
Pressure when the compressor is off: approx. 392 to 588 kPa (3.9 to 5.9 kgf/cm2, 57 to 85 psi)
Remove the windshield wiper motor and link assembly.
Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL
Remove the front outer cowl top panel sub-assembly.
for LHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for LHD)>REMOVAL
for RHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for RHD)>REMOVAL
Remove the front bumper assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL
Remove the radiator side deflector RH.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER>REMOVAL
| *a | Check for leaks |
| *b | Halogen Leak Detector Sensor |
| *c | Distance between Sensor and Joint to be Checked:
10 mm or less |
| *d | Halogen Leak Detector Sensor Moving Speed:
25 to 50 mm/sec. |
How to check for refrigerant leaks in pipe joints:
Gas leaking from a joint can be dissipated by even the slightest breeze. Move the halogen leak detector sensor 360° around each joint instead of keeping it in one spot when checking.
Using a halogen leak detector, check for refrigerant leaks at the pipe joints shown in the illustration.
| *a | Area to be Checked | *b | Service Valve (High) |
| *c | Service Valve (Low) | *d | Air Conditioner Pressure Sensor Joint |
| *e | Cooler Expansion Valve Joint | *f | Condenser Joint (Inlet) |
| *g | Condenser Joint (Outlet) | *h | Compressor Joint (Inlet) |
| *i | Compressor Joint (Outlet) | - | - |
After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes.
When checking for leaks, the presence of oily dirt at a joint can indicate a leak.
There are no refrigerant leaks from the joints.
If refrigerant is leaking, disconnect the leaking joint and visually check for the cause, such as the presence of foreign matter.
| *1 | Drain Cooler Hose |
| *a | Halogen Leak Detector |
Bring the halogen leak detector sensor close to the drain cooler hose with the detector turned off, and then turn the detector on.
Keep water away from the halogen leak detector to prevent malfunction.
After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
When bringing the halogen leak detector sensor close to the drain cooler hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.
Refrigerant is not leaking from the drain cooler hose.
If refrigerant is leaking, check for refrigerant leaks from the No. 1 cooler evaporator sub-assembly.
Remove the blower motor with fan sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>REMOVAL
| *1 | No. 1 Cooler Evaporator Sub-assembly |
| *a | Halogen Leak Detector |
Insert the halogen leak detector sensor into the air conditioning unit assembly, bring the sensor close to the No. 1 cooler evaporator sub-assembly and check for refrigerant leaks.
After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
Refrigerant is not leaking from the No. 1 cooler evaporator sub-assembly.
If refrigerant is leaking, disconnect the leaking joint and visually check for the cause, such as the presence of foreign matter.
Install the blower motor with fan sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>INSTALLATION
Install the radiator side deflector RH.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER>INSTALLATION
Install the front bumper assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION
Install the front outer cowl top panel sub-assembly.
for LHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for LHD)>INSTALLATION
for RHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for RHD)>INSTALLATION
Install the windshield wiper motor and link assembly.
Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION