Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM2030EQ _58 Vehicle Interior _014672 HEATING / AIR CONDITIONING _0074654 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to select FACE mode before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM

Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55702A 3.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55702A 4.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 87246 5.DISCONNECT HEATER OUTLET WATER HOSE

a.
E227145

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.

NOTICE:
·

Do not apply excessive force to the heater outlet water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 6.DISCONNECT HEATER INLET WATER HOSE

a.
E227146

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater inlet water hose.

NOTICE:
·

Do not apply excessive force to the heater inlet water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 88704 7.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E227144

Remove the bolt, and rotate the hook connector.


b.

Disconnect the suction hose sub-assembly.


c.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710E 8.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Disconnect the air conditioner tube and accessory assembly.


b.

Remove the O-ring from the air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 9.REMOVE FRONT SEAT ASSEMBLY LH (for RHD Manual Seat)

HINT:

Use the same procedure as for the RH side.


Hide 10.REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 86183D 11.REMOVE AUDIO AMPLIFIER COVER (for 10 Speakers)

Hide 12.REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)

Hide 13.REMOVE FRONT SEAT ASSEMBLY RH (for LHD Manual Seat)

Hide 14.REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:

Use the same procedure as for the LH side.


Hide 15.REMOVE STEERING POST ASSEMBLY

Hide 16.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 58521B 17.REMOVE FLOOR CARPET HOOK

a.
E227413C05
0.104,0.042 0.479,0.333 0.375,0.292 12 false *A 0.104,2.302 0.531,2.615 0.427,0.313 12 false *B
*A for LH Side
*B for RH Side


Disengage the 6 guides.


b.
E227415C05
0.083,0.104 0.542,0.417 0.458,0.313 12 false *A 0.083,2.417 0.521,2.698 0.438,0.281 12 false *B
*A for LH Side
*B for RH Side


Disengage the 6 claws and remove the 6 floor carpet hooks.


Hide 82730 18.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)

Hide 82730 19.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD)

Hide 88650N 21.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 85940 22.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

Hide 77306 23.DISCONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

a.
E227149

Remove the screw.


b.
E227150

Disengage the guide to disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.


Hide 58544A 24.REMOVE FLOOR CARPET BRACKET LH

a.

Disengage the guide.


b.
E227154

Turn back the floor carpet as shown in the illustration.


c.
E235070

Remove the 2 clips.


d.

Disengage the 2 guides to remove the floor carpet bracket LH.


Hide 87212F 25.REMOVE REAR NO. 2 AIR DUCT

a.
E235068

Disengage the 2 claws to remove the rear No. 2 air duct.


Hide 58569D 26.REMOVE FRONT FLOOR CAUTION PLATE COVER

a.
E234873

Using a moulding remover, disengage the claw and guide, and remove the front floor caution plate cover.


Hide 58543B 27.REMOVE FLOOR CARPET BRACKET RH

a.
E227155

Disengage the guide.


b.

Turn back the floor carpet as shown in the illustration.


c.
E235071

Remove the 2 clips.


d.

Disengage the 2 guides to remove the floor carpet bracket RH.


Hide 87212 28.REMOVE REAR NO. 1 AIR DUCT

a.
E235069

Disengage the 2 claws to remove the rear No. 1 air duct.


Hide 58861B 29.REMOVE NO. 1 CONSOLE BOX DUCT

a.
E227163

Remove the clip and No. 1 console box duct.


Hide 88625Q 30.REMOVE ROOM TEMPERATURE SENSOR (COOLER THERMISTOR)

a.
E246542

Disconnect the cooler thermistor hose and connector and remove the room temperature sensor (cooler thermistor).


Hide 55306B 31.REMOVE INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
E234877C04
2.24,2.271 1.344,2.969 false 1.177,2.906 1.604,3.188 0.427,0.281 10 false *1
*1 Earth Wire


Disconnect each connector.


b.

Disengage each clamp.


c.

Remove the bolt and disconnect the earth wire.


d.
E244265

Remove the bolt and 2 nuts.


e.

Remove the screw and instrument panel to cowl brace sub-assembly.


Hide 55307E 32.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E234879C05
2.198,0.969 3.01,0.833 false 3.01,0.729 3.313,0.99 0.302,0.26 10 false *1
*1 Earth Wire


Disconnect the connector.


b.

Disengage each clamp.


c.

Remove the bolt and disconnect the earth wire.


d.
E227165

Remove the bolt and 2 nuts.


e.

Remove the screw and No. 2 instrument panel brace sub-assembly.


Hide 55458A 33.REMOVE INSTRUMENT PANEL SAFETY PAD CAP

a.

Put protective tape around the 5 instrument panel safety pad caps.

E265293C04
2.115,1.563 2.115,1.24 false 4.875,1.292 4.875,0.969 false 0.417,0.125 0.792,0.365 0.375,0.24 12 false *A 3.771,0.115 4.146,0.354 0.375,0.24 12 false *B 2.031,1.583 2.427,1.854 0.396,0.271 10 false *1 4.792,1.302 5.188,1.573 0.396,0.271 10 false *1
*A for Driver Side *B for Passenger Side
*1 Protective Tape - -



b.

Using a screwdriver, remove the 5 instrument panel safety pad caps.


Hide 34.REMOVE FRONT LOWER PANEL PACKING

a.
E245760

Remove the 2 front lower panel packings as shown in the illustration.


Hide 35.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

NOTICE:
·

Be sure to support the air conditioning unit when removing it because failure to do so may cause the bracket of the air conditioning unit to break.

·

When disassembling the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

for 10 Speakers:

i.
E234881

Disengage the 3 clamps.



b.
E227851

Disengage the 3 claws to open the 3 clamps as shown in the illustration.


c.
E234883C04
0.896,3.844 0.24,3.438 0.24,3.438 0.604,4.031 false 2,0.354 2.458,0.646 0.458,0.292 10 false *1 0.031,3.333 0.542,3.698 0.51,0.365 12 false *A
*A w/ Smart Entry and Start System
*1 Airbag Sensor Assembly


Disconnect the connector from the airbag sensor assembly as shown in the illustration.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.

Disconnect each connector.


e.

Disengage each clamp.


f.

Using a screwdriver, disengage the 2 claws to unlock the retainer as shown in the illustration.

E227173C05
2.188,1 2.021,1.354 false 2.823,1.427 2.479,1.698 false 2.854,1.292 3.188,1.531 0.333,0.24 10 false *1 2.208,0.875 2.542,1.083 0.333,0.208 10 false *2
*1 Retainer *2 Protective Tape



g.

Disengage the claw and disconnect the airbag connector as shown in the illustration.

E227175


h.

Disengage each clamp.

E238905C02
5.292,0.74 5.75,1.427 5.75,1.427 5.885,0.958 false 5.667,1.448 6.073,1.719 0.406,0.271 10 false *1
*1 Earth Wire - -



i.

Remove the 2 bolts and disconnect the 2 earth wires.


j.
E234885

Disengage each clamp.


k.

Remove the bolt and disconnect the earth wire.

E234886C05
1.083,1.938 1.76,1.969 false 4.76,4.406 5.49,4.208 false 1.781,1.885 2.156,2.135 0.375,0.25 10 false *1 4.594,4.323 4.99,4.583 0.396,0.26 10 false *2
*1 Earth Wire *2 Connector Holder



l.

Remove the 2 nuts and disconnect the connector holder.


m.

Disconnect the connector.


n.

Disengage each clamp.


o.
E245762

Remove the 2 bolts.


p.

Remove the 3 bolts <A> and 2 bolts <B> as shown in the illustration.

E247302C01
3.344,1.417 3.208,1.458 false 3.656,1.302 3.76,1.135 false 3.75,1.646 3.865,1.531 false 2.135,0.667 2.5,0.948 0.365,0.281 10 false *a 3.135,0.667 3.5,0.948 0.365,0.281 10 false *b 4.115,0.667 4.5,0.948 0.385,0.281 10 false *c 5.083,0.667 5.448,0.948 0.365,0.281 10 false *d 3.063,1.396 3.427,1.635 0.365,0.24 10 false *1 3.771,1.021 4.094,1.229 0.323,0.208 10 false *2 3.865,1.427 4.146,1.646 0.281,0.219 10 false *3 0.146,2.948 0.604,3.229 0.458,0.281 10 false <A> 0.292,3.354 0.719,3.594 0.427,0.24 10 false <A> 0.24,3.729 0.646,3.958 0.406,0.229 10 false <A> 2.646,4.073 3.042,4.354 0.396,0.281 10 false <C> 5.875,2.594 6.344,2.813 0.469,0.219 10 false <B> 5.917,2.896 6.375,3.156 0.458,0.26 10 false <B>
*1 Movable Collar *2 Body
*3 Instrument Panel Reinforcement - -
*a Step 1 *b Step 2
*c Step 3 *d Step 4



q.

Remove the bolt <C> and nut.


r.

Disconnect the cooler drain hose.


s.

Disengage the 3 guides and remove the instrument panel reinforcement with air conditioning unit as shown in the illustration.

E248492


Hide 36.REMOVE AIR CONDITIONING UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioning unit assembly from the instrument panel reinforcement assembly.

E248493