1.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Engage the 5 guides and temporarily install the instrument panel safety pad assembly as shown in the illustration.
Do not damage the instrument panel safety pad assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.
Install the 2 clips.
Install the 3 bolts <B> and nut <D>.
Install the 2 passenger airbag bolts <A>.
Install the glove box light as shown in the illustration.
Engage each clamp.
Connect each connector.
82142A
2.CONNECT NO. 2 INSTRUMENT PANEL WIRE
55011A
3.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Engage the 10 clips to install the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
55480D
4.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
for LHD:
Connect the connector.
Engage the 3 clips and guide to install the lower instrument panel finish panel assembly.
58816B
5.INSTALL CONSOLE BOX INSERT
for RHD:
Engage the 2 claws to connect the room temperature sensor.
Engage the clip and 4 guides as shown in the illustration.
Install the console box insert with the 2 screws <C>.
58817A
6.INSTALL FRONT NO. 2 CONSOLE BOX INSERT
for LHD:
Engage the 2 claws to connect the room temperature sensor.
Engage the clip and 4 guides as shown in the illustration.
Install the front No. 2 console box insert with the 2 screws <C>.
86160P
7.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSTALLATION
55409F
8.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 2 guides.
Engage the 3 claws and 2 clips to install the No. 2 instrument panel speaker panel sub-assembly.
62211
9.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
86160J
10.INSTALL FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)
55510F
11.INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY
Connect the connector.
Engage the 6 clips to install the No. 1 speaker opening cover assembly.
86160P
12.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
55408F
13.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 2 guides.
Engage the 3 claws and 2 clips to install the No. 1 instrument panel speaker panel sub-assembly.
62212
14.INSTALL FRONT PILLAR GARNISH LH
55670
15.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 10 clips to install the No. 3 instrument panel register assembly.
55303B
16.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Engage the 2 clips and 4 guides.
Install the 3 screws <C>.
Close the lower instrument panel door.
Install the lower instrument panel sub-assembly with the bolt <B> and screw <C>.
55607
17.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect the connector.
Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.
55317A
18.INSTALL INSTRUMENT SIDE PANEL RH
Engage the 3 guides as shown in the illustration.
Engage the 4 claws to install the instrument side panel RH as shown in the illustration.
62311B
19.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62111A
20.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
67913
21.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
22.INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)
23.INSTALL NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)
74110E
24.INSTALL FRONT ASH RECEPTACLE ASSEMBLY
Connect each connector.
Engage the 2 clips.
Install the front ash receptacle assembly with the 2 screws <C>.
58831A
25.INSTALL FRONT CONSOLE UPPER PANEL GARNISH
Connect the connector.
Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.
55660
26.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Connect the connector.
Engage the 4 clips to install the No. 2 instrument panel register assembly.
When installing the No. 2 instrument panel register assembly, check that the wire harness is not caught between the No. 2 instrument panel register assembly and duct.
55405B
27.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Engage the 7 clips and 2 guides to install the center instrument cluster finish panel sub-assembly.
28.INSTALL CONSOLE BOX ASSEMBLY
58815A
29.INSTALL CONSOLE BOX CARPET
58864B
30.INSTALL NO. 4 CONSOLE BOX DUCT
58801E
31.INSTALL UPPER CONSOLE BOX SUB-ASSEMBLY
58805C
32.INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
33504F
33.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
53921B
34.INSTALL FRONT PANEL GARNISH RH
Engage the 3 clips and 8 guides to install the front panel garnish RH.
55432D
35.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
for LHD:
Engage the 5 clips and 3 guides.
Install the lower No. 1 instrument panel finish panel with the 2 bolts <B>.
for RHD:
Connect the connector.
Engage the 4 claws, 7 clips and 3 guides.
Install the lower No. 1 instrument panel finish panel with the 2 bolts <B>.
53601
36.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
53922B
37.INSTALL FRONT PANEL GARNISH LH
Engage the 3 clips and 8 guides to install the front panel garnish LH.
83100
38.INSTALL COMBINATION METER ASSEMBLY
55410C
39.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Temporarily install the instrument cluster finish panel assembly as shown in the illustration.
Connect each connector.
for LHD:
Engage the 3 claws, 7 clips and 4 guides.
for RHD:
Engage the 4 claws, 5 clips and 4 guides.
Engage the 4 clips and 2 guides to install the instrument cluster finish panel assembly.
55650
40.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 4 clips to install the No. 1 instrument panel register assembly.
55431B
41.INSTALL UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)
Connect the connector.
Engage the 2 claws and 4 clips to install the upper instrument panel finish panel.
55318C
42.INSTALL INSTRUMENT SIDE PANEL LH
Engage the 3 guides.
Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
62312B
43.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62112A
44.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
67914
45.INSTALL FRONT DOOR SCUFF PLATE LH
46.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
47.INSPECT SRS WARNING LIGHT