Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2030EQ _59 Vehicle Exterior _014678 MIRROR (EXT) _0074700 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Reverse Shift-linked Function of Power Mirrors does not Operate  


SYSTEM DESCRIPTION

On receiving a reverse signal from the park/neutral position switch assembly, the ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU. Each outer mirror control ECU then performs control in response to the reverse signal.

HINT:

The reverse shift-linked function will not activate when the mirror select switch is in the neutral position (off).


WIRING DIAGRAM

B309281E05
5.854,4.896 7.156,5.208 1.302,0.313 10 false Mirror Sub-assembly RH 4.917,3.323 5.51,3.573 0.594,0.25 10 false RM+R 3.542,4.844 3.875,5.094 0.333,0.25 10 false z6 4.906,4.219 5.479,4.5 0.573,0.281 10 false RMVR 4.594,1.115 5.094,1.438 0.5,0.323 10 false CAN 2.969,0.948 3.396,1.188 0.427,0.24 10 false CAN 3.292,1.115 3.698,1.417 0.406,0.302 10 false CAN 0.76,0.969 1.344,1.292 0.583,0.323 10 false CAN 4.615,3.813 5.083,4.083 0.469,0.271 10 false CAN 5.417,0.479 5.729,0.75 0.313,0.271 10 false 10 5.417,1.365 5.594,1.573 0.177,0.208 10 false 1 4.938,0.594 5.583,1.021 0.646,0.427 10 false LM+R 4.135,1.99 4.521,2.281 0.385,0.292 10 false z5 4.917,1.5 5.531,1.927 0.615,0.427 10 false LMVR 5.417,3.188 5.76,3.521 0.344,0.333 10 false 10 5.417,4.083 5.76,4.438 0.344,0.354 10 false 1 5.854,2.156 7.156,2.469 1.302,0.313 10 false Mirror Sub-assembly LH 4.135,2.156 5.698,2.625 1.563,0.469 10 false Outer Mirror Control ECU Assembly (Driver Door) 2.458,4.177 4.115,4.667 1.656,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 1.417,3.115 2.74,3.646 1.323,0.531 10 false Park/Neutral Position Switch Assembly 0.583,3.979 1.125,4.292 0.542,0.313 10 false ECM 0.583,3.823 1.188,4.188 0.604,0.365 10 false E26 1.417,2.958 1.792,3.229 0.375,0.271 10 false E4 0.969,2.448 1.208,2.677 0.24,0.229 10 false R 0.958,1.688 1.26,2.052 0.302,0.365 10 false P 1.813,2.448 2.177,2.729 0.365,0.281 10 false RL 1.813,1.677 2.24,1.938 0.427,0.26 10 false PL 1.177,1.552 1.448,1.74 0.271,0.188 10 false 70 1.177,2.333 1.563,2.635 0.385,0.302 10 false 68 1.625,1.563 1.844,1.823 0.219,0.26 10 false 3 1.615,2.333 1.833,2.604 0.219,0.271 10 false 2 0.802,5.375 2.75,5.771 1.948,0.396 10 false : CAN Communication Line 3.531,5 5.771,5.313 2.24,0.313 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 0.125,0.073 1.042,0.479 0.917,0.406 12 false for LHD:

B309281E06
5.854,2.156 7.156,2.469 1.302,0.313 10 false Mirror Sub-assembly RH 4.906,0.583 5.427,0.802 0.521,0.219 10 false RM+R 4.146,1.99 4.417,2.198 0.271,0.208 10 false z6 4.896,1.49 5.469,1.75 0.573,0.26 10 false RMVR 4.594,1.104 5.01,1.354 0.417,0.25 10 false CAN 2.958,0.948 3.458,1.313 0.5,0.365 10 false CAN 3.302,1.115 3.792,1.458 0.49,0.344 10 false CAN 0.771,0.958 1.375,1.302 0.604,0.344 10 false CAN 4.615,3.813 5.01,4.063 0.396,0.25 10 false CAN 5.417,0.479 5.76,0.781 0.344,0.302 10 false 10 5.417,1.365 5.635,1.604 0.219,0.24 10 false 1 4.927,3.323 5.469,3.635 0.542,0.313 10 false LM+R 3.563,4.802 3.833,5.083 0.271,0.281 10 false z5 4.927,4.208 5.563,4.563 0.635,0.354 10 false LMVR 5.417,3.208 5.75,3.479 0.333,0.271 10 false 10 5.417,4.083 5.667,4.323 0.25,0.24 10 false 1 5.854,4.875 7.156,5.188 1.302,0.313 10 false Mirror Sub-assembly LH 4.146,2.156 5.708,2.625 1.563,0.469 10 false Outer Mirror Control ECU Assembly (Driver Door) 2.448,4.177 4.083,4.667 1.635,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 1.417,3.115 2.74,3.594 1.323,0.479 10 false Park/Neutral Position Switch Assembly 0.583,3.979 1.156,4.375 0.573,0.396 10 false ECM 0.583,3.823 1.01,4.083 0.427,0.26 10 false E26 1.417,2.958 1.792,3.208 0.375,0.25 10 false E4 0.958,2.448 1.26,2.719 0.302,0.271 10 false R 0.958,1.677 1.313,2.021 0.354,0.344 10 false P 1.813,2.448 2.167,2.75 0.354,0.302 10 false RL 1.813,1.688 2.167,1.938 0.354,0.25 10 false PL 1.167,1.563 1.49,1.854 0.323,0.292 10 false 70 1.167,2.333 1.51,2.667 0.344,0.333 10 false 68 1.615,1.563 1.771,1.75 0.156,0.188 10 false 3 1.615,2.333 1.854,2.583 0.24,0.25 10 false 2 0.802,5.385 2.781,5.771 1.979,0.385 10 false : CAN Communication Line 3.563,4.99 5.75,5.385 2.188,0.396 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 0.125,0.073 1.177,0.583 1.052,0.51 12 false for RHD:

CAUTION / NOTICE / HINT

HINT:

The reverse shift-linked function will not activate when the mirror select switch is in the neutral position (off).


PROCEDURE

1.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C09
0.156,0.063 0.313,0.229 0.156,0.167 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

Result:
Result Proceed to
Memory and reactivation functions are normal. A
Memory function is not normal. B
Reactivation function is not normal. C




A

2.CHECK CAN COMMUNICATION SYSTEM

B

GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirror Surface Position is not Memorized)

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirrors do not Return to Memorized Position)

2.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTC is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

3.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Check if SFI system DTCs are output.

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

SFI system DTCs are not output.


Result:
Proceed to
OK
NG




OK

4.CHECK COMBINATION METER ASSEMBLY

NG

GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

4.CHECK COMBINATION METER ASSEMBLY
a.

Check if the shift position indicator light in the combination meter assembly operates normally.

OK:

The shift position indicator light indicates the actual shift position correctly.



Result:
Proceed to
OK
NG



OK

5.CHECK REVERSE SHIFT-LINKED FUNCTION

NG

GO TO METER / GAUGE SYSTEM (PROBLEM SYMPTOMS TABLE)

5.CHECK REVERSE SHIFT-LINKED FUNCTION
a.
B294057C01
0.177,0.052 0.354,0.25 0.177,0.198 10 *a
*a Downward


Turn the engine switch on (IG).


b.

Set the mirror select switch to L or R.


c.

Check that the mirror surface turns downward when the shift lever is moved to R.

Result:
Result Proceed to
Reverse shift-linked functions on both mirrors are not normal A
Reverse shift-linked function on RH side is not normal B
Reverse shift-linked function on LH side is not normal C




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

C

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)