Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.02–2015.04
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU connector is disconnected from the skid control ECU.

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation is not possible.

·

The brake booster assembly is judged to be defective.


WIRING DIAGRAM

C243441E05
0.604,0.729 1.031,0.875 0.427,0.146 10 CANH 0.604,1.385 1.042,1.531 0.438,0.146 10 CANL 4.313,2.49 4.75,2.781 0.438,0.292 10 CANL 4.313,3.094 5.031,3.51 0.719,0.417 10 CANH 6.219,2.5 6.719,2.771 0.5,0.271 10 CANL 6.219,3.104 6.719,3.448 0.5,0.344 10 CANH 1.177,0.75 1.625,1.219 0.448,0.469 10 I13 1.177,1.417 1.531,1.656 0.354,0.24 10 I13 2.344,2.688 2.604,3 0.26,0.313 10 19 5.948,2.979 6.219,3.26 0.271,0.281 10 26 5.938,2.385 6.188,2.719 0.25,0.333 10 14 6.219,4.896 6.51,5.198 0.292,0.302 10 IG1 5.938,4.771 6.198,4.948 0.26,0.177 10 28 6.219,5.74 6.667,6.042 0.448,0.302 10 GND1 5.563,8.01 5.979,8.271 0.417,0.26 10 A49 2.615,2.792 2.948,3.198 0.333,0.406 10 SW 2.76,3.521 3.052,3.771 0.292,0.25 10 I18 2.76,3.667 4.635,4.021 1.875,0.354 10 Combination Meter Assembly 1.99,4.865 3.458,5.281 1.469,0.417 10 from IG1 NO. 2 Relay 4.406,5.031 5.521,5.333 1.115,0.302 10 ECU-IG1 NO. 1 5.552,8.167 7.094,8.667 1.542,0.5 10 Skid Control ECU (Brake Actuator Assembly) 0.521,5.521 0.948,5.802 0.427,0.281 10 PKB 0.448,5.76 0.708,5.99 0.26,0.229 10 12 0.177,8.156 1.271,8.427 1.094,0.271 10 Main Body ECU 1.198,7.125 1.521,7.552 0.323,0.427 10 3D 1.208,6.938 1.427,7.26 0.219,0.323 10 20 2.083,5.594 2.417,5.906 0.333,0.313 10 1 2.292,5.708 2.531,5.979 0.24,0.271 10 + 3.115,5.75 3.417,6.042 0.302,0.292 10 E 1.99,7.031 2.333,7.26 0.344,0.229 10 1 3.333,5.594 3.615,5.844 0.281,0.25 10 2 1.49,6.042 1.938,6.375 0.448,0.333 10 A30 1.479,6.198 4.01,6.667 2.531,0.469 10 Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 2,7.563 2.427,7.813 0.427,0.25 10 A42 2,7.719 3.365,8.177 1.365,0.458 10 Parking Brake Switch Assembly 5.948,5.615 6.229,5.917 0.281,0.302 10 38 4.823,2.958 5,3.104 0.177,0.146 10 16 4.823,2.365 5,2.51 0.177,0.146 10 15 1.198,1.198 1.5,1.469 0.302,0.271 10 13 1.198,0.552 1.573,0.927 0.375,0.375 10 14 2.188,7.229 2.313,7.375 0.125,0.146 10 + 6.219,4.115 6.604,4.427 0.385,0.313 10 +BS 5.938,3.99 6.219,4.271 0.281,0.281 10 25 2.573,4.094 3.49,4.396 0.917,0.302 10 from Battery 4.49,4.271 5.302,4.542 0.813,0.271 10 ABS NO. 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C238832C32
0.177,0.698 0.656,1.021 0.479,0.323 1.26,1.51 0.958,0.76 false 0.375,2.729 0.729,1.604 false 2.813,1.469 3.021,0.76 false 0.24,0.167 0.521,0.594 0.281,0.427 10 *a 0.313,0.781 0.75,1.188 0.438,0.406 10 A49 0.208,2.75 0.5,2.906 0.292,0.156 10 +BS 0.823,0.583 1.104,0.74 0.281,0.156 10 IG1 2.771,0.583 3.177,0.74 0.406,0.156 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A49 skid control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-25 (+BS) - Body ground Always 11 to 14 V
A49-25 (+BS) - A49-38 (GND1) Always 11 to 14 V
A49-28 (IG1) - Body ground Ignition switch ON 11 to 14 V
A49-28 (IG1) - A49-38 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C238832C33
0.208,0.719 0.688,1.042 0.479,0.323 2.823,1.5 2.219,0.75 false 0.271,0.198 0.594,0.563 0.323,0.365 10 *a 0.344,0.802 0.792,1.198 0.448,0.396 10 A49 1.948,0.563 2.552,0.938 0.604,0.375 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-38 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH ASSEMBLY)
a.

Reconnect the A49 skid control ECU connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Parking Brake SW
50003 105 38

e.

Using the intelligent tester, check the switch operation signal received when the parking brake is operated.

OK:

When the parking brake is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY
7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.
C230719C05
2,2 2.458,2.771 false 1.51,2 1.021,2.771 false 0.365,0.302 0.74,0.802 0.375,0.5 10 *a 2.427,2.792 2.729,3.01 0.302,0.219 10 + 0.896,2.792 1.271,3 0.375,0.208 10 E
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))


Turn the ignition switch off.


b.

Remove the reservoir filler cap and the strainer.


c.

Disconnect the A30 brake fluid level warning switch connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (E) Switch OFF (Float up) 1.9 to 2.1 kΩ
1 (+) - 2 (E) Switch ON (Float down) Below 1 Ω


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-19 (SW) - A30-1 (+) Always Below 1 Ω
I18-19 (SW) - Body ground Always 10 kΩ or higher
A30-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the I18 combination meter assembly connector and the A30 brake fluid level warning switch connector.


b.

Perform an Active Test of the combination meter assembly (meter CPU) using the intelligent tester.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Brake
50004 122 21

c.

Check the combination meter assembly.

OK:

The brake warning light turns on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.
C211519C05
1.646,1.969 0.844,2.802 false 0.375,0.292 0.542,0.458 0.167,0.167 10 *a 0.75,2.802 1.104,3.115 0.354,0.313 10 +
*a Component without harness connected
(Parking Brake Switch Assembly)


Turn the ignition switch off.


b.

Disconnect the A42 parking brake switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - Body ground Parking brake switch ON
(Switch pin free)
Below 1 Ω
1 (+) - Body ground Parking brake switch OFF
(Switch pin pushed in)
10 kΩ or higher



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH ASSEMBLY)

B

REPLACE PARKING BRAKE SWITCH ASSEMBLY

C

REPLACE PARKING BRAKE SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the 3D main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-20 (PKB) - A42-1 (+) Always Below 1 Ω
3D-20 (PKB) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR